How to Change the Oil in a 2015 Husqvarna FE250HQ: A Complete Guide for MotoSport.com
Shop parts for a 2015 Husqvarna FE250HQ Dirt Bike.
Maintaining your 2015 Husqvarna FE250HQ with regular oil changes ensures optimal performance and long engine life. This guide covers every essential step, from the tools you’ll need to model-specific tips, making it accessible even for new owners. Follow this detailed procedure to keep your bike in prime condition.
Tools & Supplies Needed
- 10mm, 13mm, and 8mm sockets (with ratchet and extensions)
- Drain pan
- Funnel
- Torque wrench
- Clean rags or shop towels
- Oil filter (OEM or high-quality aftermarket)
- New copper or aluminum crush washers (for drain plugs)
- Fresh engine oil: SAE 10W-50 full synthetic (per Husqvarna spec)
- Measuring cup or graduated beaker
- Gloves and goggles (for safety)
- Service manual (optional, for reference)
Preparation
- Warm up the engine for about 3-5 minutes to help the oil flow and suspend contaminants.
- Place the bike on a stand to keep it upright and secure.
- Lay out all tools and supplies in a clean work area.
Step-by-Step Oil Change Process
-
Remove the Skid Plate
- If installed, use a socket or T-handle to remove fasteners and set the skid plate aside. This gives clear access to the drain plugs and oil screens.
-
Drain the Engine Oil
- Place the drain pan under the engine.
- On the 2015 FE250HQ, there are typically two drain bolts: one for the main sump and a smaller one for the oil chamber (both usually near the bottom left side of the engine).
- Use the correct socket to remove each plug. Be careful, as the oil will be hot.
- Let all the oil drain completely. Inspect and replace crush washers on the drain bolts if worn or flattened.
-
Clean and Inspect Oil Screens
- Carefully remove and inspect the oil screens located near the drain bolts (if equipped: check your manual).
- Clean them with brake cleaner or contact cleaner. Inspect for debris or metal shavings, which might indicate internal wear.
- Reinstall the clean screens.
-
Replace the Oil Filter
- Locate the oil filter cover on the right side of the engine. Remove the bolts holding it in place using the 8mm socket.
- Pry off the cover gently. Remove the old filter and O-ring/seal (replace with new if included in your kit).
- Before inserting the new filter, prime it by dipping it in fresh oil. This ensures lubrication on startup.
- Install the new filter and carefully align the cover. Start bolts by hand to avoid cross-threading. Torque to 7 ft-lbs for the cover bolts (as specified for similar Husqvarna models)1.
-
Reinstall Drain Bolts
- Once oil has drained, reinstall both drain bolts with new crush washers.
- Tighten to the manufacturer's specified torque. For Husqvarna 250/350/501 models, typical specs are 10-15 Nm (7-11 ft-lbs); always confirm with your owner’s manual.
-
Add New Engine Oil
- Remove the oil fill cap on the right side of the engine.
- Pour in 1.25 to 1.3 liters (approx. 1300 mL) of 10W-50 synthetic oil – check the exact capacity in your Husqvarna service manual, but the FE250 is similar to the FE501, which takes 1.3L1.
- If the filter cavity fills slowly, you can tip the bike to the left slightly to pre-charge the oil filter housing, but do not overfill.
- Reinstall the oil fill cap, wipe up any spills.
-
Start the Engine and Check Oil Level
- Start the engine and let it idle for 30 seconds to circulate oil. Shut it off and let it sit for 2–3 minutes.
- Check the oil level using the sight glass (right side, near the clutch cover). Oil should register between halfway and three-quarters in the window2.
- Add more oil if needed, in small amounts.
-
Final Inspection
- Double-check all bolts for tightness and look for leaks around the drain bolts and oil filter cover.
- Reinstall the skid plate if removed.
- Dispose of old oil and filter correctly at an approved recycling center.
Model-Specific Callouts for 2015 Husqvarna FE250HQ
- This model shares many engine and frame characteristics with the FE350 and FE501, so general oil change procedures are virtually identical.
- The oil capacity is 1.25–1.3L. Overfilling can lead to engine trouble – always check the sight glass on level ground after cycling the oil.
- Oil filter cover torque spec is 7 ft-lbs. Overtightening may warp the cover or damage the O-ring.
- Use high-quality 10W-50 synthetic to maintain warranty and performance.
- Change the oil after the first hour of riding on a new bike, then every 15 hours or after each race — critical for high-performance engines3.
- Inspect oil screens for unusual debris on every change; excessive metal may indicate the need for professional inspection.
Tips for a Clean, Easy Oil Change
- Lay out all tools and parts before starting.
- Consider using a magnetic tray for bolts to avoid losing hardware.
- Always torque bolts per spec – hand tight is not enough for critical fasteners.
- Keep a record of each oil change (date, hours, oil brand/viscosity) for maintenance tracking and warranty.
Regularly changing the oil in your 2015 Husqvarna FE250HQ is the best way to keep your bike in peak condition for years of reliable riding. If in doubt, consult your official Husqvarna service manual.
Proprietary content for MotoSport.com. All rights reserved.
Related Shopping Categories
Shop Motor Oil for a 2015 Husqvarna FE250HQ Dirt Bike.
Shop Oil Filters for a 2015 Husqvarna FE250HQ Dirt Bike.
Shop Oil Drain Pans for a 2015 Husqvarna FE250HQ Dirt Bike.
Shop Tools for a 2015 Husqvarna FE250HQ Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2015 Husqvarna FE250HQ Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.