How to Change the Oil in a 2014 Yamaha YZ250F – MotoSport.com Complete Guide

Shop parts for a 2014 Yamaha YZ250F Dirt Bike.

Regular oil changes are critical for optimal performance and longevity of your 2014 Yamaha YZ250F. The following guide details the tools required, exact procedures, and special tips specific to this model, ensuring your bike receives the care it needs after every hard session. This guide is proprietary content from MotoSport.com.

Tools and Supplies Needed

  • Socket set: 8mm (oil filter cover), 10mm (oil strainer), 12mm (drain bolt)
  • Oil pan
  • New oil filter: OEM or K&N 140 or equivalent
  • Fresh oil: Yamalube 10W-40 or quality equivalent (check owner’s manual for oil capacity)
  • New drain bolt washer (crush washer) – always replace
  • Clean rags
  • Funnel (ideally with a measuring cup)
  • Torque wrench – for correct bolt tightness
  • Safety gloves
  • Oil disposal container (for recycling old oil)

Step-by-Step Oil Change Procedure for 2014 YZ250F

  1. Warm Up the Engine
    • Start the bike and let it idle for 3–5 minutes. This thins the oil and suspends contaminants which drain out more efficiently.
  2. Secure the Bike
    • Shut off the engine. Support the bike upright on a stand to ensure safe access and thorough draining.
  3. Remove the Oil Filler Cap
    • Loosen and remove the oil filler cap on top of the engine. This prevents a vacuum and allows oil to drain quickly.
  4. Drain the Old Oil
    • Locate the oil drain bolt (12mm) beneath the engine, beside the frame rail.
    • Position your oil pan underneath and carefully remove the drain bolt and crush washer. Let the oil drain completely.
  5. Remove and Replace the Oil Filter
    • Locate the oil filter cover on the engine, secured with 8mm bolts.
    • Remove the cover evenly to avoid warping.
    • Discard the old filter and O-ring/gasket.
    • Clean the mating surface of any debris or old oil.
    • Install a fresh O-ring and insert your new oil filter (make sure the orientation matches the manual).
    • Reinstall and torque cover bolts evenly as specified in the owner’s manual.
  6. Inspect and Clean the Oil Strainer
    • The YZ250F features an oil strainer accessible through a 10mm bolt on the opposite engine side. Remove, inspect, clean, and reinstall the strainer.
  7. Replace the Drain Bolt and Washer
    • Install a new crush washer on the drain bolt.
    • Re-tighten the drain bolt to the specified torque. Do NOT overtighten.
  8. Add Fresh Oil
    • Use a funnel, pour in the recommended engine oil (Yamalube 10W-40 or similar), using the owner’s manual to verify quantity (approx. 1.0–1.1 quarts for 2014 YZ250F, but always check your manual).
    • It’s better to slightly underfill than overfill since removing excess oil is more work than adding a bit more.
  9. Check Oil Level
    • Replace the filler cap.
    • Start the engine and let it idle briefly, then shut off and let it sit for a minute. Check the oil sight glass—oil should be between the upper and lower lines.
    • Top up if needed, avoiding overfill.
  10. Inspect for Leaks and Clean Up
    • Check around the drain bolt, oil filter cover, and strainer for leaks.
    • Clean up any residual oil.
    • Properly dispose of the old oil and filter at a recycling center.

Specific 2014 Yamaha YZ250F Call-Outs

  • This 2014 YZ250F does not have a separate oil tank like older two-strokes—the oil goes straight into the crankcase.
  • The oil filter orientation and matching the O-ring are important; improper installation can cause leaks or oil starvation.
  • This model has an oil strainer that should be cleaned every oil change.
  • Always use a new crush washer on the drain bolt every change to prevent leaks.
  • Recommended oil type is Yamalube 10W-40; do not use car oil or oil with friction modifiers.
  • Check the sight glass for oil level with the bike upright and the engine cool for the most accurate reading.
  • Depending on how hard you ride and your environment, change intervals may vary—track riders may need changes every 4–7 hours of runtime.

Final Checklist Before Riding

  • Double-check all bolts for correct torque
  • Check for oil leaks after the first short ride
  • Record the service interval for your next oil change (consider using the Yamaha app)
  • Dispose of all hazardous waste responsibly

Keeping up with regular oil changes is one of the simplest and best ways to ensure your 2014 Yamaha YZ250F delivers top performance every time you ride. For all your high-quality oil and filters, MotoSport.com stocks everything you need for this job and all your dirt bike maintenance.

Related Shopping Categories

Shop Motor Oil for a 2014 Yamaha YZ250F Dirt Bike.

Shop Oil Filters for a 2014 Yamaha YZ250F Dirt Bike.

Shop Oil Drain Pans for a 2014 Yamaha YZ250F Dirt Bike.

Shop Tools for a 2014 Yamaha YZ250F Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Yamaha YZ250F Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.