How to Change the Oil in a 2014 Yamaha TW200 – Complete Guide

Shop parts for a 2014 Yamaha TW200 Dirt Bike.

Regular oil changes are vital for the longevity and smooth performance of your 2014 Yamaha TW200. This step-by-step guide, proprietary to MotoSport.com, explains everything you need – from the tools required to crucial call-outs specific to the 2014 model.

Tools and Supplies Needed

  • 17mm or 19mm socket and ratchet (for drain plug; check your bike, as some vary)
  • Small torque wrench (set to 43 Nm for drain plug)
  • Pliers (optional, for stubborn fill cap)
  • Clean rags
  • Oil catch pan
  • Funnel
  • Replacement oil (use 10W-40 motorcycle oil, API grade SG or higher, JASO MA certified, approx. 1.06 quarts / 1.0 L)
  • OEM oil filter/strainer (if planning to replace)
  • Replacement drain plug O-ring (recommended)
  • Gloves (recommended)

Preparation Steps

  • Warm up the engine with a short 2–3 minute ride. Warm oil drains faster and more completely. Don't overheat – just get it warm to the touch.
  • Park the bike on level ground and shut it off. Put it on the center stand or use a bike stand to keep it upright.
  • Turn off the ignition and ensure the bike is stable before proceeding.

Changing the Oil – Step by Step

  1. Remove the Fill Cap:
    • Locate the oil fill cap on the right side of the engine. Wipe away dirt or debris to avoid contamination.
    • Unscrew the fill cap and set it aside. This step helps the oil flow out more smoothly during draining.
      Tip: If stuck, use pliers carefully.
  2. Remove the Drain Plug:
    • Place your oil catch pan directly under the drain bolt.
    • Use a 17mm or 19mm socket and ratchet to loosen and remove the drain plug at the bottom of the engine.
    • Note: The drain plug assembly on the TW200 contains a spring and wire mesh strainer. Be prepared to catch these as they come out so they don't fall into your oil drain pan and get lost. Carefully inspect and clean the strainer.
    • Let all the oil drain completely. This may take several minutes.
  3. Inspect and Replace Parts:
    • While the oil is draining, clean the wire mesh strainer and inspect it for debris or metal filings. Replace if damaged.
    • Wipe the O-ring on the drain plug. Replace the O-ring with a new one for a better seal and to prevent leaks.
    • Inspect the sealing surface around the drain to ensure it is clean and free of dirt or debris before reassembly.
  4. Reinstall the Drain Plug Assembly:
    • Reassemble the drain plug with:
      • The cleaned wire mesh strainer
      • The spring
      • The new O-ring
    • Screw the drain plug into place by hand to avoid cross-threading.
    • Torque the plug to 43 Nm (or as specified in your owner’s manual).
  5. Replace the Oil Filter (if required):
    • The oil filter element is located on the right side of the engine (consult your manual for access specifics).
    • If replacing, remove the cover, swap in a new filter, and be careful to position new O-rings as needed.
  6. Add New Oil:
    • Place a funnel in the fill hole.
    • Add 1.06 US quarts (1.0 Liter) of 10W-40 oil, pausing halfway to let it settle.
    • Reinstall the fill cap securely by hand.
  7. Start Your Engine and Recheck:
    • Start the bike and let it idle for about a minute. Inspect for leaks at the drain plug and oil filter.
    • Turn off the engine and let the bike sit upright for another minute to allow the oil to settle.
  8. Verify Oil Level:
    • Check the oil level in the sight glass on the right side of the engine.
      The oil should be between the upper and lower lines with the bike vertical (not on side stand).
    • If needed, add oil in small increments until the level is correct – don't overfill.
  9. Final Steps:
    • Clean any spilled oil.
    • Dispose of old oil in accordance with local laws.
    • Reinstall skid plate if removed.
    • Take a short ride and recheck the oil level. Top off if required.

2014 Yamaha TW200 – Specific Call-Outs

  • The 2014 TW200 takes about 1.06 US quarts (1.0 Liter) of oil for a full change including filter. Be careful not to overfill, as overfilling can cause engine issues.
  • The wire mesh strainer (not a paper cartridge filter) is unique to the TW200 – clean it thoroughly and handle carefully during reinstallation.
  • Always install new O-rings where specified (drain plug, filter assembly) to avoid any future oil leaks.
  • Use only JASO MA rated oils suitable for wet clutches – avoid energy conserving or automotive oils.
  • If you removed the skid plate, be sure to reinstall before riding.

Helpful Tips

  • Keep the bike upright when checking the oil in the sight glass to ensure an accurate level reading.
  • Don't overtighten the drain plug; use a torque wrench to avoid damage.
  • If this is your first oil change, take your time and stay organized with your parts.

Changing the oil on your 2014 Yamaha TW200 is straightforward and a perfect DIY task. With practice, it will take you around 30 minutes. If you need OEM parts or high-quality oil, visit MotoSport.com for fast shipping and expert support.

Related Shopping Categories

Shop Motor Oil for a 2014 Yamaha TW200 Dirt Bike.

Shop Oil Filters for a 2014 Yamaha TW200 Dirt Bike.

Shop Oil Drain Pans for a 2014 Yamaha TW200 Dirt Bike.

Shop Tools for a 2014 Yamaha TW200 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Yamaha TW200 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.