How to Change the Oil in a 2014 Husqvarna TC250: Step-by-Step Guide
Shop parts for a 2014 Husqvarna TC250 Dirt Bike.
Changing the oil in your 2014 Husqvarna TC250 is a vital maintenance task to keep your dirt bike running strong and performing its best on the track. This detailed, MotoSport.com-exclusive guide walks you through the process and addresses all model-specific pointers so you can complete your oil change with confidence.
Tools and Supplies Needed
- 10mm/12mm wrench or socket (likely 12mm for drain bolt, confirm with your service manual)
- Drain pan (to collect old oil)
- Replacement engine oil (check your Husqvarna manual for recommended viscosity and volume; most TC250 models require about 0.8 to 1.0 liter of high-quality 4-stroke oil)
- New crush washer (for the drain bolt)
- Shop towels or rags
- Funnel (for adding new oil)
- Torque wrench (preferred, for reinstalling drain bolt to specs)
- Parts brush and contact cleaner (to clean up around the drain area)
- Pick tool or small pair of pliers (for oil screen removal/inspection)
- Gloves and eyewear (for safety)
Pre-Oil Change Preparation
- Warm up the engine for about 3-5 minutes to thin the oil; this helps it drain out more completely.
- Set the bike on a stable stand in a well-ventilated, clean area.
- Give the area around the drain bolt a quick wipe with a shop towel to prevent dirt from falling in the engine.
Step-by-Step Oil Change on a 2014 Husqvarna TC250
-
Remove the skid plate (if equipped):
You’ll need access to the bottom of the engine case, so take off any skid plate using the necessary wrench or socket. -
Locate and loosen the drain bolt:
The drain bolt is usually found on the bottom or side of the crankcase. For most TC250 models, it's a 12mm bolt. Loosen it carefully with your wrench.
Model-specific callout: The oil drain bolt area is tight. Use care not to drop the bolt into the pan or onto the ground–it's easy to get oil on your hands or miss catching the bolt, so have a rag handy for cleanup. Some owners recommend using a dental pick or a pick tool to help remove the oil screen sitting behind the drain bolt, which can be a snug fit.
Source: Remove the plastic skid plate and get out the dental tools... After you loosen the 12mm drain bolt (easy) the challenge is to get the drain bolt out without dropping something or wearing the oil. There is only one screen on this model (behind the drain bolt)... it is definitely a snug fit in the bore. -
Drain the old oil:
Place your drain pan under the bolt and fully remove the bolt and its crush washer. Allow all oil to completely drain. A slight tilt of the bike (about 30 degrees towards you) will help evacuate any remaining oil from the bottom of the engine case. -
Remove and inspect the oil screen:
Carefully pull out the oil screen using your pick tool or pliers. Clean the screen with contact cleaner and a brush, inspect it for any metal debris or damage, and reinstall once clean.
Model-specific callout: For the TC250, there's a single oil screen situated behind the drain bolt. Take extra care when removing it—the fit is tight, but it will come out with gentle, steady force. -
Replace the crush washer and reinstall the drain bolt:
Always use a new crush washer to prevent leaks. Reinstall the drain bolt, tightening to the manufacturer's recommended torque spec (refer to your owner's manual, but typically around 15-20 Nm for many dirt bikes). -
Fill with new oil:
Remove the oil fill cap located at the top or side of the engine case. Using a funnel, add fresh oil to the engine. For the 2014 TC250, the oil capacity is about 0.80 liters (0.85 quarts). Always verify with your owner's manual for the exact amount.
Tip: Start by filling a little less than the full amount, check the oil level using the sight glass or dipstick, and add more as needed to reach the correct level. -
Check for leaks and final oil level:
Reinstall the fill cap, start the engine, and let it run for a minute. Shut the engine off and wait a few minutes. Re-check the oil level and top off if necessary. -
Dispose of old oil and clean up:
Pour used oil into a sealed container and take it to a local auto parts store or recycling center.
2014 Husqvarna TC250 Oil Change: Owner-Specific Tips
- Engine is a 4-stroke single: The TC250 has a separate oil sump; oil changes are quick with no oil filter to replace—just clean and check the oil screen.
- Drain bolt access is cramped: Take your time and have shop towels nearby for cleanup; a steady hand helps prevent dropping tools or bolts into the drain pan.
- Tight oil screen fit: If you find the screen difficult to remove, gently use a pick or curved tool—avoid forcing it so you don’t puncture the screen mesh.
- Always verify torque and oil type: Service manuals will have required values and specifics. Confirm you’re using oil that meets Husqvarna’s recommended specs for your riding style.
Conclusion
Performing regular oil changes on your 2014 Husqvarna TC250 is crucial for reliable performance and longevity. With proper tools and these step-by-step instructions, you’ll keep your bike in peak condition—ready for the next ride.
Related Shopping Categories
Shop Motor Oil for a 2014 Husqvarna TC250 Dirt Bike.
Shop Oil Filters for a 2014 Husqvarna TC250 Dirt Bike.
Shop Oil Drain Pans for a 2014 Husqvarna TC250 Dirt Bike.
Shop Tools for a 2014 Husqvarna TC250 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2014 Husqvarna TC250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.