How to Change the Oil in a 2014 Husqvarna FE501HQ — Step-by-Step Guide

Shop parts for a 2014 Husqvarna FE501HQ Dirt Bike.

Keeping up with regular oil changes is essential for the longevity and performance of your 2014 Husqvarna FE501HQ. This guide, proprietary to MotoSport.com, will walk you through the process, highlight required tools, and include key notes specific to your bike model.

Tools and Supplies Needed

  • Socket set (metric, typically 8mm and 13mm sockets)
  • Torque wrench
  • Oil drain pan
  • Clean rags
  • Plastic or rubber gloves
  • Flat-head screwdriver or T-handle
  • New oil filter (factory spec)
  • Fresh engine oil (Motorex SAE 10W-50, 1200 mL)
  • Replacement crush washer (for the drain bolt, recommended)
  • Funnel

Preparation

  • Warm up the engine:– Let your bike idle for 3-5 minutes. Warm oil drains faster and more thoroughly.
  • Park safely:– Use a bike stand on even ground. Ensure the engine is off and cool enough to handle.
  • Remove the skid plate if your bike has one — this grants easy access to drain plugs and filter covers .

Oil Change Steps for 2014 Husqvarna FE501HQ

  1. Drain the Engine Oil
    • Locate the main drain bolt (bottom of the crankcase) and place your oil pan underneath.
    • Remove the bolt with your socket and let oil drain completely.
    • Inspect the drain plug and crush washer for wear — replace the washer if deformed.
  2. Remove the Oil Filter
    • Use the socket or screwdriver to remove the oil filter cover (typically found on the engine's right side).
    • Pull out the old oil filter. Tip:– Pre-lubricate your new filter with a touch of engine oil for immediate protection at startup .
    • Inspect the old filter for metal shavings or debris; if found, investigate further before completing the oil change.
  3. Inspect & Clean Oil Strainers (if equipped)
    • The 2014 FE501HQ uses two oil screens that should also be removed and cleaned. Use your socket set to unscrew both (locations: behind the drain plug and near the filter housing).
    • Wash the screens in fresh solvent or parts cleaner; check for debris.
  4. Install the New Filter and Refit All Plugs
    • Install the new oil filter, making sure the rubber O-ring is lightly coated in engine oil for a proper seal.
    • Replace the filter cover and tighten bolts to factory torque spec; don't overtighten aluminum components.
    • Reinstall cleaned oil screens, main and secondary drain bolts with the new washer, tightening to the correct torque setting.
  5. Add Fresh Engine Oil
    • Remove the oil fill cap on the right side of the engine and insert a clean funnel.
    • Pour in 1200 mL of oil (or per manual's spec for 2014 FE501HQ). Call-out:– Always confirm this amount in your owner's manual, as overfilling can damage the engine .
    • Replace the oil fill cap and ensure it's tight.
  6. Check Oil Level and Final Steps
    • Start the engine and let it idle for three minutes.
    • Turn the engine off and let the bike sit for a minute or two so oil can settle.
    • Check the sight glass (located near the clutch cover) — oil should be between halfway and three-quarters up the window .
    • If low, top off carefully. Avoid overfilling.
    • Check for leaks around drain and filter area; wipe off excess oil with a rag.
    • Reinstall your skid plate if removed.

Model-Specific Call-Outs for 2014 Husqvarna FE501HQ

  • First oil change:– Husqvarna recommends the first oil replacement after the initial hour of break-in. Thereafter, replace oil every 15 hours of ride time or after every race for optimal reliability .
  • Drain bolts:– The 2014 model features multiple drain points (main, long filter screw, short filter screw). Ensure all are removed, cleaned, and refitted during each oil change .
  • Filter orientation:– Insert the new oil filter in the same direction as the old one was removed.
  • O-rings:– Inspect O-rings on the filter cover and replace if cracked or flattened. A damaged O-ring will cause leaks.
  • Oil type:– Husqvarna recommends a synthetic 10W-50 oil for dual-sport use. Confirm you're using top-quality oil to protect your high-performance engine .
  • Sight glass monitoring:– The sight glass gives a fast, accurate read of oil level. If you don't see oil, add more slowly and recheck.

Tips for a Cleaner Oil Change

  • Use a large drain pan to avoid oil splashing.
  • Dispose of old oil and filter properly at a recycling facility.
  • Log your oil change date/hours for better service tracking.
  • Wipe spills immediately to prevent slippery spots in your workspace.

Changing the oil in your 2014 Husqvarna FE501HQ is straightforward with the right tools and preparation. Following this guide ensures your engine stays healthy and ready for every adventure.

For all your parts and service needs — trust MotoSport.com for quality and expertise.

Related Shopping Categories

Shop Motor Oil for a 2014 Husqvarna FE501HQ Dirt Bike.

Shop Oil Filters for a 2014 Husqvarna FE501HQ Dirt Bike.

Shop Oil Drain Pans for a 2014 Husqvarna FE501HQ Dirt Bike.

Shop Tools for a 2014 Husqvarna FE501HQ Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husqvarna FE501HQ Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.