How to Change the Oil in a 2014 Husqvarna FC250

Shop parts for a 2014 Husqvarna FC250 Dirt Bike.

Keeping your 2014 Husqvarna FC250 maintained with regular oil changes is vital for performance and longevity. Here’s a step-by-step, MotoSport.com proprietary guide to performing an oil change on this specific model. The FC250 shares its core engine design with several KTM and Husqvarna models, but there are a few specific tips exclusive to the 2014 FC250 worth noting for owners.

Tools & Supplies Needed

  • Socket wrench set (metric)
  • Torque wrench
  • Oil drain pan
  • Replacement oil filter (recommended OEM)
  • Crush washer (always replace)
  • Contact cleaner
  • Clean rags
  • Measuring cup
  • Pin wrench (for oil screen, 14mm or as specified)
  • Engine oil (Consult manual for viscosity, typically 10W-50 Full Synthetic for Husqvarna FC250)

Preparation Steps

  • Run the engine until it reaches operating temperature. This ensures the oil flows freely and removes more debris during the draining process.
  • Turn off the bike and place it on a level surface using a stand. Ensure the bike is stable before beginning work.

Step-By-Step Process

  1. Place a drain pan under the engine, ensuring it will catch all draining oil.
    Tip: Position the pan slightly forward, oil drains at an angle on this model.
  2. Use the correct socket to remove the oil drain plug (typically located on the bottom left of the engine case). Allow the oil to fully drain.
    Caution: The oil may be hot; use gloves if needed.
  3. While the oil drains, remove the screw plug with the oil screen (check your manual for the exact tool, a pin wrench is typically used). This is often overlooked, but it is essential on the 2014 FC250 to clean out fine debris that accumulates on the screen.
    Carefully pull out the screen, wipe it thoroughly, and inspect for metallic debris that could indicate excessive engine wear.
  4. Remove the oil filter cover using the appropriate socket (usually 8mm or 10mm bolts). Take out the old filter, noting its orientation.
    Before installing the new filter, it’s recommended to pour a small amount of fresh oil onto the filter. This helps prime it and ensures immediate oil flow upon start-up.
  5. Clean all sealing surfaces and verify that the old crush washer is removed. Always replace the washer with a fresh one to prevent leaks.
  6. Reinstall the cleaned oil screen with new O-rings if provided (very important for proper sealing on this model), and torque the screw to spec (check your owner’s manual for exact values).
  7. Install a new oil filter, ensuring correct orientation. Replace the oil filter cover and tighten all bolts to manufacturer torque specifications.
  8. Reinstall the main oil drain plug with the new crush washer and torque it properly.
  9. Using a measuring cup, fill with fresh engine oil. The 2014 FC250 requires approximately 1.0 liter–however, always refer to your manual and check sight glass level when done.
    Pour the oil into the fill port on top of the engine.
  10. Reinstall the oil filler cap. Start the bike and let it idle for 2–3 minutes. Observe for leaks.
  11. Stop the engine and let it sit for a minute. Check the oil level in the sight glass (on the right crankcase cover). Oil should be between the minimum and maximum marks.
  12. Top off if necessary, but do not overfill.

2014 Husqvarna FC250 Specific Call-Outs

  • Always clean the oil screen when changing the oil. This is critical on the FC250, as small particles can collect here and impact oil flow.
  • Use OE quality filters to maintain the correct oil pressure and flow. Third-party filters may cause premature wear or reduced performance.
  • Replace all crush washers and O-rings whenever disturbed to prevent slow oil leaks, which the 2014 model is known to develop if reused.
  • Torque values are important—overtightening can crack the cases, while undertightening can cause leaks. Always use a calibrated torque wrench as specified in your service manual.
  • The recommended oil change interval is generally every 15 running hours or more frequently under race or high-stress conditions. Husqvarna officially recommends every 6000 km, but dirt bikes should be changed far more frequently due to the harsher operating environment.

Maintaining your 2014 Husqvarna FC250 with regular oil changes is crucial. By following each step closely and using quality tools and components, you’ll keep your dirt bike running strong and ready for your next ride.

For all your oil change kits, tools, and OEM parts, trust MotoSport.com—the dirt bike expert’s choice.

Related Shopping Categories

Shop Motor Oil for a 2014 Husqvarna FC250 Dirt Bike.

Shop Oil Filters for a 2014 Husqvarna FC250 Dirt Bike.

Shop Oil Drain Pans for a 2014 Husqvarna FC250 Dirt Bike.

Shop Tools for a 2014 Husqvarna FC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husqvarna FC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.