How to Change the Oil in a 2014 Husaberg FE501

Shop parts for a 2014 Husaberg FE501 Dirt Bike.

Changing the oil in your 2014 Husaberg FE501 is one of the most important routine maintenance tasks you can do to keep your dirt bike running strong and extend the life of the engine. Not only does fresh oil ensure smooth operation, but it also helps prevent premature engine wear due to dirt and debris. This comprehensive guide, proprietary to MotoSport.com, covers every step, including the specific tools needed, relevant tips, and model-specific call-outs.

Tools and Materials Needed

  • Socket wrench set (8mm, 13mm sockets recommended)
  • Drain pan
  • Clean rags or shop towels
  • Torque wrench
  • Rubber gloves (optional, for cleanliness)
  • Motorex SAE 10W-50 oil (check exact capacity in manual; typically –1.2L for this model)
  • Factory-spec oil filter
  • Replacement crush washer for drain bolt
  • Small flathead screwdriver (if you need to assist in filter removal)
  • Skid plate removal tool (if skid plate is present/installed)

Preparation Steps

  • Warm up the engine for a few minutes. Warm oil drains faster and carries more sediment and debris out of the engine.
  • If your bike has a skid plate, remove it to access the drain bolts and oil filter housing.
  • Set the bike upright and secure it safely on a stand.

Step-by-Step Oil Change Process

  1. Locate the Oil Drain Bolts and Oil Filter:
    • The 2014 FE501 has a main drain screw on the engine case bottom and oil filter cover on the right side.
  2. Drain the Old Oil:
    • Place your drain pan under the engine.
    • Remove the main drain bolt gently with a socket wrench. Be careful—oil may be hot.
    • Allow the oil to drain completely. Rock the bike gently, if needed, to ensure all oil flows out.
  3. Clean and Inspect Components:
    • Remove and inspect the crush washer; replace if damaged.
    • Wipe the area around the drain hole clean, checking for residual debris or metal particles.
  4. Remove the Oil Filter:
    • Using the appropriate socket or Allen key, remove the oil filter cover screws.
    • Remove the oil filter; you may need a small flathead to gently help it out.
    • Inspect the filter for metal shavings or large debris, which could indicate internal engine issues.
    • Clean the filter cavity and oil filter cover thoroughly with a clean rag.
  5. Clean the Oil Screen(s):
    • Your FE501 also has an oil screen(s) that should be removed and cleaned. Typically located near the drain plug; consult your owner's manual for the exact location.
    • Clean screens using brake cleaner or fresh oil and reinstall when dry.
  6. Install New Oil Filter:
    • Lightly lubricate the new oil filter's O-ring with fresh oil for a proper seal.
    • Install the new filter, ensuring it is seated properly. Reinstall the filter cover and torque the bolts per manual spec (refer to your manual for exact torque values).
  7. Reinstall Drain Plug:
    • Install the drain plug with a new crush washer and tighten with a torque wrench to the manufacturer’s recommended spec.
  8. Pour in Fresh Oil:
    • Remove the filler cap. Using a funnel, add Motorex SAE 10W-50 (approximately 1.2L, or as specified in your manual).
    • Install the oil fill cap.
  9. Check Oil Level:
    • Start the bike and let it idle for one minute. Shut it off and let sit for a minute, then check the oil sight glass or dipstick as specified by manufacturer.
    • Add oil as needed to reach the correct level.
  10. Reinstall Skid Plate and Clean Up:
    • If removed, reinstall your skid plate securely.
    • Dispose of the old oil and filter properly at a recycling center.

2014 Husaberg FE501 Model-Specific Call-Outs

  • Oil Capacity: Approximately 1.2L, but always check your owner’s manual for the exact specification.
  • Oil Filter Access: The oil filter is located on the right side of the engine; access is straightforward with skid plate removed.
  • Screen Cleaning: This model uses oil screens in addition to the paper oil filter; inspect and clean them during every oil change to extend engine life.
  • Torque Specs: Refer to your owner's manual or service manual for all drain and filter cover bolt torque settings to prevent overtightening and potential engine case damage.
  • Oil Change Frequency: Recommended every 15 hours of operation, or after every race, for optimal engine health.
  • Parts Compatibility: Many parts crossover with Husqvarna FE501 and KTM 500 EXC-F models for the same years, but always double-check fitment before ordering supplies.

Conclusion

Changing the oil in your 2014 Husaberg FE501 is a critical maintenance routine that can be accomplished by most dirt bike owners with basic tools and these clear steps. Keeping up with oil changes will maintain your bike’s performance and reliability for every ride.

Related Shopping Categories

Shop Motor Oil for a 2014 Husaberg FE501 Dirt Bike.

Shop Oil Filters for a 2014 Husaberg FE501 Dirt Bike.

Shop Oil Drain Pans for a 2014 Husaberg FE501 Dirt Bike.

Shop Tools for a 2014 Husaberg FE501 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husaberg FE501 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.