How to Change the Oil in a 2014 Husaberg FE450

Shop parts for a 2014 Husaberg FE450 Dirt Bike.

Keeping your 2014 Husaberg FE450 in top condition requires timely oil changes to protect the engine and ensure optimal performance. The process is straightforward for those familiar with dirt bike maintenance. This guide, proprietary to MotoSport.com, will walk you through the entire oil change process, highlight specific call-outs for the FE450, and list all tools you need to get the job done efficiently and cleanly.

Tools and Materials Needed

  • Socket wrench set (for drain bolt and oil filter cover bolts)
  • Oil filter wrench (if required for your filter)
  • Drain pan
  • New oil filter (recommended for every oil change)
  • Fresh engine oil (see owner's manual for viscosity and specification; typical fill is 1200 ml for this model)
  • Replacement sealing washers/O-rings (as needed for drain plugs and oil screens)
  • Clean rags or shop towels
  • Torque wrench (optional, for precise tightening of drain bolts)
  • Rubber gloves (optional, for cleaner hands)
  • Phillips or flathead screwdriver (to remove plastics or skid plate if present)

Steps to Change the Oil

  1. Preparation:
    • Start your bike and let it idle for a few minutes to warm up the oil. This helps the oil flow more freely and removes more contaminants with it.
      Important: Make sure the engine is not hot to avoid burns.
    • Turn off the bike and put it on a level surface, using a bike stand if possible.
    • Remove the skid plate or lower engine guards if your bike is equipped with one, to access the drain plugs.
  2. Drain the Old Oil:
    • Place a drain pan underneath the engine.
    • Locate the main oil drain plug and remove it using the appropriate socket wrench. Be careful as hot oil may gush out rapidly.
    • Let the engine oil drain completely. While it drains, also remove the two side oil screen plugs (short and long oil screens) and carefully extract the screens. Inspect these screens for debris, which can indicate early warning signs of engine wear.
      Do not remove any screw or bolt that is not specifically identified as an oil drain or oil screen plug.
  3. Clean Components:
    • Thoroughly clean the drain plug, as well as the oil screens and their sealing surfaces. Replace the sealing washer or O-rings if they appear worn or damaged.
    • If the drain plug has a magnetic tip, check for metal particulates. A small amount of fine metal dust is normal, but large chunks or an excessive amount may indicate problems.
  4. Replace the Oil Filter:
    • Remove the oil filter cover (typically secured by two or three bolts).
    • Remove the used oil filter and note its orientation for proper reinstallation.
    • Lightly oil the gasket on the new filter before installing it to ensure a good seal and easy removal next time.
    • Install the new oil filter, then replace and tighten the oil filter cover bolts.
  5. Reinstall Plugs and Screens:
    • Reinstall the cleaned oil screens (short and long types), ensuring their O-rings are in good condition and seated properly.
    • Reinstall the main oil drain plug with a new sealing washer if required.
    • Tighten all plugs and screens to the manufacturer's torque specifications (typically hand-tight plus a gentle nudge with a wrench, or use a torque wrench for precise tightening).
  6. Add Fresh Oil:
    • Remove the oil fill cap on top of the engine case.
    • Using a clean funnel, pour in the recommended amount of oil (for the FE450, 1200 ml is typical, but always double-check your owner's manual or engine case marking for exact volume).
  7. Check Oil Level:
    • Start the engine and let it run for about three minutes.
    • Turn off the engine, let it settle for one to two minutes, then check the oil level in the sight glass. The oil should sit about halfway up to three-quarters in the window.
    • Top off if needed but avoid overfilling.
  8. Finish Up:
    • Reinstall the skid plate or engine guard.
    • Wipe down any spilled oil from the engine and frame.
    • Properly dispose of used oil and filter according to local environmental regulations.

Specific Call-Outs for the 2014 Husaberg FE450

  • This engine uses two oil screens (short and long) in addition to the main drain plug. Both need to be removed, cleaned, and checked for debris at each oil change.
  • The oil change interval recommendation is every 10–15 hours or after each race, and always after the initial break-in period. The first oil change should be done after the first ride (or about 1 hour), the second at around 3 hours, and then at regular intervals thereafter.
  • Some owners change the filter at every oil change, while others do so every other change. For best engine protection, it's wise to replace the oil filter with every change.
  • Always check for updated specs in your owner's manual, as oil type and volume can be updated by the manufacturer.
  • When cleaning the oil screens, inspect both for metal debris or foreign material, which may indicate a need for further engine inspection.

Conclusion

Changing the engine oil on your 2014 Husaberg FE450 is an essential maintenance task that keeps your dirt bike running smoothly and extends engine life. By following these detailed steps and paying attention to the unique requirements of your model, you ensure the best possible performance for every ride.

Ride safe and keep your engine fresh—MotoSport.com has you covered for all your parts and maintenance needs.

Related Shopping Categories

Shop Motor Oil for a 2014 Husaberg FE450 Dirt Bike.

Shop Oil Filters for a 2014 Husaberg FE450 Dirt Bike.

Shop Oil Drain Pans for a 2014 Husaberg FE450 Dirt Bike.

Shop Tools for a 2014 Husaberg FE450 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husaberg FE450 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.