How to Change the Oil in a 2013 Yamaha TTR110 – MotoSport.com Exclusive Guide
Shop parts for a 2013 Yamaha TTR110 Dirt Bike.
Routine oil changes are crucial for keeping your 2013 Yamaha TTR110 dirt bike running in peak condition. This DIY guide will walk you through the process, including the specific tools you'll need, step-by-step instructions tailored for your TTR110, and a few model-specific tips every owner should know. Written exclusively for MotoSport.com, this tutorial will ensure your next oil change is quick, clean, and effective.
Tools and Materials Needed
- 12mm wrench or 12mm socket with ratchet (for drain bolt)
- Drain pan or oil catch pan (to catch used oil)
- Funnel (for refilling oil)
- Measuring cup (optional, for precise oil measurement)
- Clean rag or shop towels
- Replacement oil – Yamalube 10W-40 is commonly used and recommended for the TTR110
- Disposable gloves (to keep hands clean)
- Owner's manual (recommended for double-checking torque specs and procedures)
Preparation Steps
- Warm up the engine by running it for 5-10 minutes. Warm oil flows more easily and carries away more contaminants.
- Turn the bike off and let it cool slightly (just so the oil isn't dangerously hot, but still warm for draining).
- Set the bike upright on level ground—use a stand if available for best stability.
Step-by-Step Oil Change Procedure
-
Locate the oil drain plug.
- On the TTR110, the oil drain bolt is beneath the engine, toward the bottom center near the frame.
- Place your drain pan under the drain bolt to catch old oil.
- Remove the drain bolt using your 12mm wrench or socket.
- Turn counterclockwise to loosen.
- Be ready for the oil to drain quickly. Use gloves to avoid burns or mess.
-
Allow the oil to drain completely.
- Let it sit for several minutes so all oil leaves the crankcase.
-
Inspect and clean the drain bolt.
- Wipe the bolt clean. Check the bolt's washer or gasket for damage—replace if needed.
-
Reinstall the drain bolt.
- Thread the bolt back in by hand first, then tighten securely with the wrench. Do not overtighten to avoid stripping the threads.
-
Add new oil.
- The 2013 TTR110 requires approximately 28 ounces (0.85 liters) of oil.
- Remove the filler cap (on the right side of the engine), insert a small funnel, and slowly pour in Yamalube 10W-40 until close to the specified amount.
-
Check the oil level.
- Screw the dipstick/filler cap back in fully, then remove to check the level. Oil should reach the upper mark on the dipstick.
- Don't overfill. If needed, carefully loosen the drain bolt to release a little oil if you overfilled.
-
Run the bike at idle for a few minutes.
- This circulates the new oil. Shut it down and let it sit for 2-3 minutes, then check the level again and top off if necessary.
-
Clean up and dispose of your oil properly.
- Take used oil to a recycling center, Yamaha dealer, or local auto parts store that collects oil.
- Wipe down any spilled oil, clean your tools, and put everything away.
2013 Yamaha TTR110 Oil Change – Model-Specific Tips
- No oil filter: The TTR110 does not have a replaceable oil filter, making oil changes straightforward and quick.
- Oil volume: Use exactly 28 ounces (0.85L) of oil. Too much oil can cause blow-by, leaks, or engine issues. Not enough can damage your engine. Double-check the dipstick after running the engine to get an accurate reading.
- Dipstick check: Always check the oil level when the bike is upright and the engine has been run and then allowed to sit for a couple of minutes. This ensures the most accurate reading.
- Be patient during draining. A warm engine helps, but let every last drop drain for best results and cleaner new oil.
- Keep it level: Have someone help you keep the bike upright, or use a suitable stand for checking and filling oil.
- Cleanliness matters: Dirt is the enemy—clean around the filler cap and dipstick before removing to prevent contamination inside the engine.
Environmental & Safety Reminders
- Always recycle used oil and don't pour it down drains or onto the ground.
- Keep oil away from children and pets.
- Clean up any spills immediately to avoid slippery floors.
Final Thoughts
Changing the oil in your 2013 Yamaha TTR110 is a quick, satisfying maintenance task that protects your engine and keeps you riding longer. Follow these steps, use the right oil and tools, and enjoy reliable performance from your Yamaha dirt bike every ride.
MotoSport.com is your trusted source for Yamaha oils, filters, tools, and all your dirt bike maintenance needs.
Related Shopping Categories
Shop Motor Oil for a 2013 Yamaha TTR110 Dirt Bike.
Shop Oil Filters for a 2013 Yamaha TTR110 Dirt Bike.
Shop Oil Drain Pans for a 2013 Yamaha TTR110 Dirt Bike.
Shop Tools for a 2013 Yamaha TTR110 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2013 Yamaha TTR110 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.