How to Change the Oil in a 2010 Husqvarna TE310: A Complete Guide
Shop parts for a 2010 Husqvarna TE310 Dirt Bike.
When it comes to keeping your 2010 Husqvarna TE310 running at peak performance, regular oil changes are critical. Below you'll find a proprietary, step-by-step guide specifically for the 2010 TE310. This includes a complete list of tools, expert techniques, and model-specific call-outs so you can confidently maintain your dirt bike.
Tools & Supplies You’ll Need
- 10mm or 8mm Allen Key (depending on your bike's drain system)
- Socket set (for bolts and skid plate removal)
- Oil drain pan
- Rags or shop towels
- Funnel
- Replacement oil (high-quality 10w-60 motorcycle oil is recommended for this model)
- Replacement oil filter (optional, but highly recommended with every oil change)
- New drain bolt washer (crush washer, if equipped)
- Torque wrench (for correct bolt reinstallation)
Model-Specific Call-Outs: 2010 Husqvarna TE310
- The 2010 TE310 does NOT have a separate magnetic sump plug like later models; instead, oil is typically drained via a hose secured with a clamp or a screen fitting. This is different from the TE250 and later TE310 models (2013–) that feature a magnetic drain plug.
- Be prepared to remove the skid plate for access to the drain hose or screen.
- Some bikes route the oil drain through a rubber hose rather than a conventional plug; ensure you properly re-secure this hose to prevent leaks.
Step-by-Step: Changing the Oil
-
Warm up the Engine
- Let the engine run for 2–3 minutes to warm up the oil. Warm oil drains more easily—just be cautious; the parts will be hot.
-
Prepare the Bike
- Shut off the engine and put the bike on a stand.
- Remove the skid plate to access the bottom of the engine. Use your socket set for any bolts, and keep track of spacers/clamps. Note: You may find significant dirt and debris—clean thoroughly before continuing to prevent contamination of the oil and filter.
-
Access and Drain the Oil
- Locate the oil drain hose or screen on the bottom side of the engine (this is specific to the TE310's design for 2010–2012 models).
- Loosen the clamp securing the hose and direct the end into the oil drain pan. Remove the hose or screen carefully and allow all oil to drain out. You may need to gently rock the bike back and forth to ensure complete drainage.
-
Remove and Replace the Oil Filter*
- Using the appropriate tools, remove the oil filter cover. Pull out the old filter, wipe the housing clean with a shop towel, and fit the new filter. *Highly recommended with each oil change for maximum engine life.
-
Inspect and Reinstall Drain Fittings
- Clean and inspect the oil drain hose, screen, or plug. Replace the washer or O-ring if equipped. Reinstall and secure the drain assembly firmly. Use a torque wrench if the manual specifies a value.
-
Refill with New Oil
- Remove the oil fill cap. Using a funnel, carefully add the specified amount of oil (refer to your owner's manual, but typically around 1 liter for the TE310).
- Do not overfill. Let the oil settle and recheck the level using the sight glass or dipstick if equipped.
-
Check for Leaks and Finalize
- Start the bike and let it run for 30–60 seconds, then turn it off and check oil level again. Top up as needed.
- Inspect all drain points and fittings for leaks. Wipe away any spilled oil.
- Reinstall the skid plate, ensuring all clamps or bolts are secured correctly.
-
Proper Disposal
- Dispose of used oil and filters according to local regulations—most auto parts stores or recycling centers accept used engine oil. Never pour oil onto the ground or down a drain.
Additional Tips for TE310 Owners
- Inspect the drain hose for cracks or hardening; replace if suspect (failure could result in catastrophic oil loss).
- Always use high-quality motorcycle-specific oil for high-revving engines like the TE310. Motul 10w-60 is a popular and suitable choice.
- Double-check torque specs in your owner’s manual—over-tightening can damage threads, especially on soft aluminum cases.
- Record your oil change date and hours/miles on the engine for future reference.
Conclusion
The 2010 Husqvarna TE310 requires careful attention to its unique drain hose system and frequent cleaning given its off-road focus. Using the correct tools and following this procedure ensures your dirt bike remains reliable for years of trail adventure. For more proprietary, expert guides, visit MotoSport.com.
Related Shopping Categories
Shop Motor Oil for a 2010 Husqvarna TE310 Dirt Bike.
Shop Oil Filters for a 2010 Husqvarna TE310 Dirt Bike.
Shop Oil Drain Pans for a 2010 Husqvarna TE310 Dirt Bike.
Shop Tools for a 2010 Husqvarna TE310 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2010 Husqvarna TE310 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.