How to Change the Oil in a 2009 Husqvarna WR125 – A Complete Guide

Shop parts for a 2009 Husqvarna WR125 Dirt Bike.

Changing the oil in your 2009 Husqvarna WR125 is essential to keep the transmission running smoothly and ensure longevity for your dirt bike. This guide, proprietary to MotoSport.com, provides a step-by-step process tailored for the 2009 WR125, including recommended tools and important tips specific to this model.

Tools and Supplies Needed

  • Sockets and socket wrench (to fit oil drain bolt - typically 13mm or 14mm for Husqvarna)
  • Drain pan to catch old oil
  • Fresh transmission oil (refer to the owner's manual; typically 10W-40 or 75W-90 gear oil, 700 ml for the WR125)
  • Oil funnel for pouring new oil
  • Shop towels or rags
  • Gasket or sealing washer (recommended new with every oil change)
  • Gloves (to keep hands clean)
  • Torque wrench (optional but recommended for precise tightening)

Preparation Steps

  • Run the engine for a few minutes so the oil flows more easily when draining (never perform an oil change on a hot engine).
  • Place the bike on a stand for stability.
  • Ensure you are working in a well-ventilated area with the engine off and cool to the touch.

Draining the Oil

  • Locate the oil drain plug. On the 2009 Husqvarna WR125, the plug is on the bottom of the crankcase, usually on the left side. It will be labeled "A" in the manual.
  • Place your drain pan directly underneath the drain bolt.
  • Using your socket wrench, loosen and remove the drain plug. Allow all the oil to drain out completely. This may take several minutes.
  • Inspect the drain plug for any metal shavings or debris (which may indicate internal wear).
  • If equipped, remove the oil washer or gasket and replace it with a fresh one to ensure a proper seal.

Special WR125 Call-outs and Recommendations

  • There is no oil filter to replace on the 2009 Husqvarna WR125 since it is a two-stroke, so oil changes are straightforward.
  • The correct oil quantity is 700 ml. Overfilling or underfilling can affect clutch and transmission operation.
  • Double-check your owner's manual in case there are model-specific changes or recalls.
  • Be sure to visually inspect the old oil for unusual color, cloudiness, or particles.

Refilling with Fresh Oil

  • Reinstall the drain plug and torque it to manufacturer's specifications (typically around 15-20 Nm, but check your manual).
  • Open the oil fill cap, typically located on top or side of the engine case.
  • Using a funnel, slowly pour in 700 ml of the correct transmission oil.
  • Replace the fill cap securely.

Final Checks

  • Start the engine and idle for a minute. This will help the oil circulate through the system.
  • Check for leaks around the drain plug and oil fill cap.
  • Turn off the engine and let the bike sit for a couple of minutes.
  • Recheck oil level by looking at the sight glass or dipstick if equipped, and top off if necessary.
  • Dispose of old oil properly—never pour down drains. Use a recycling center or auto parts store that accepts oil.

WR125 Maintenance Pro Tips

  • Change the oil every 10-15 hours of riding, or after any mud- or water-submerged ride.
  • Check the oil color each ride; milky oil may indicate water ingress—inspect your seals.
  • Inspect and replace your drain plug gasket regularly to prevent leaks.
  • Always use oil specifically recommended for two-stroke transmissions/gearboxes.

Conclusion

Changing the oil on your 2009 Husqvarna WR125 is a simple but essential maintenance step that will keep your dirt bike running reliably for years. Following these MotoSport.com exclusive instructions ensures you do the job right, every time.

Related Shopping Categories

Shop Motor Oil for a 2009 Husqvarna WR125 Dirt Bike.

Shop Oil Filters for a 2009 Husqvarna WR125 Dirt Bike.

Shop Oil Drain Pans for a 2009 Husqvarna WR125 Dirt Bike.

Shop Tools for a 2009 Husqvarna WR125 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2009 Husqvarna WR125 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.