How to Change the Transmission Oil in a 2000 Yamaha PW50

Shop parts for a 2000 Yamaha PW50 Dirt Bike.

Proper maintenance is vital to keep your 2000 Yamaha PW50 running reliably, and one of the simplest yet most important tasks is changing the transmission oil. Keeping the transmission oil fresh helps reduce wear, ensures smooth shifting, and prolongs the life of your bike's components. This guide, brought to you by MotoSport.com, provides a detailed, step-by-step method tailored specifically for the 2000 Yamaha PW50.

Tools and Supplies Needed

  • 12mm socket and ratchet
  • New transmission oil (Yamalube or a high-quality alternative recommended by Yamaha)
  • Measuring cup (with clear markings to 0.3 liters)
  • Oil drain pan
  • Funnel
  • Rubber gloves
  • Shop rags
  • New drain bolt gasket/crush washer (replace every oil change)
  • Torque wrench

Important Notes for 2000 Yamaha PW50 Owners

  • This procedure applies to all model years of the PW50, including the 2000 model, as the transmission design is unchanged across years.
  • The correct oil change quantity is 0.30 liters (0.32 US qt, 0.26 Imp. qt).
  • Tighten the drain bolt to 14 Nm (10 ft-lbf) of torque.
  • Always check for leaks before and after changing the oil.
  • The bike uses a separate tank for injector oil; make sure not to confuse this with the transmission oil.

Step-by-Step Oil Change Procedure

  • Warm up the engine.
    Let the bike idle for a few minutes to get the oil flowing and make the draining process more effective. Shut off the engine before proceeding.
  • Stabilize your bike.
    Place the bike on a centerstand or ensure it is upright and level to help the old oil drain completely.
  • Locate the drain bolt and filler cap.
    The drain bolt is on the lower right side of the transmission case. The filler cap is located at the top of the case.
  • Prepare your supplies.
    Put on rubber gloves. Place the drain pan beneath the drain bolt to catch the used oil.
  • Remove the filler cap.
    Taking off the cap at the top will allow the oil to drain more freely and quickly.
  • Remove the drain bolt and old gasket.
    Use your 12mm socket to loosen and remove the drain bolt. Allow all old oil to drain into the pan. Inspect the crush washer/gasket and replace it with a new one every time.
  • Clean and inspect parts.
    Wipe down the area around the drain plug and filler cap with a shop rag. Clean the drain bolt before reinstallation.
  • Reinstall the drain bolt with new gasket.
    Thread the drain bolt back in by hand to prevent cross-threading. Use a torque wrench to tighten to 14 Nm (10 ft-lbf)–do not overtighten to avoid damaging the threads.
  • Refill the transmission with new oil.
    Using a funnel and a precise measuring cup, pour in 0.30 liters of the recommended transmission oil.
  • Reinstall and tighten the filler cap.
    Screw the filler cap back on securely.
  • Check for leaks and oil level.
    Start the bike and let it idle briefly, then shut off. Look for any leaks at the drain plug and filler cap area. Check that the oil level is correct if your bike has an inspection port (check owner's manual for details).
  • Dispose of old oil responsibly.
    Take used oil to a recycling center or an appropriate disposal location—never pour it down the drain or onto the ground.

Service Interval Recommendations

  • If the PW50 is brand new: Change the oil after the first month.
  • After initial service, change the oil again at six months.
  • For general use: Change the transmission oil once every year or check periodically based on usage.

Common Questions and Tips for the 2000 PW50

  • Can I use any oil? It is highly recommended to use oil specifically designed for two-stroke transmissions, such as Yamalube. Generic motor oils are not recommended as they may not provide adequate protection and could cause shift issues or clutch slippage.
  • Can I use old gaskets? Never reuse old crush washers or gaskets; always replace with new to avoid leaks.
  • Is injector oil the same as transmission oil? No, the PW50 uses separate reservoirs for injector oil (two-stroke oil for premix lubrication of the engine) and transmission oil. Make sure you do not confuse the two reservoirs.
  • How can I tell if my transmission oil needs changing? Dirty, dark, or gritty oil upon inspection is a clear sign that a change is overdue.
  • What if I spilled oil? Wipe up spills immediately—to protect painted surfaces and avoid any oily residue collecting dirt.

Conclusion

Changing the transmission oil on your 2000 Yamaha PW50 is straightforward and takes less than 10 minutes with the right tools. Routine oil changes are your best defense against transmission problems, ensuring your PW50 remains ready for family fun. For genuine Yamaha parts, tools, and top-tier service supplies, always trust MotoSport.com.

Related Shopping Categories

Shop Motor Oil for a 2000 Yamaha PW50 Dirt Bike.

Shop Oil Filters for a 2000 Yamaha PW50 Dirt Bike.

Shop Oil Drain Pans for a 2000 Yamaha PW50 Dirt Bike.

Shop Tools for a 2000 Yamaha PW50 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2000 Yamaha PW50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.