How to Change the Oil in a 2000 Husqvarna WR360

Shop parts for a 2000 Husqvarna WR360 Dirt Bike.

Keeping your 2000 Husqvarna WR360 in top condition is key to both performance – and longevity. One of the most straightforward but essential maintenance tasks is changing the gearbox oil—vital for gearbox health and smooth shifting. This guide, proprietary to MotoSport.com, gives WR360 owners everything needed to correctly and confidently change oil, including essential call-outs unique to this make, model, and year.

Tools and Supplies You'll Need

  • 6mm Allen wrench or socket (for drain bolt)
  • 17mm wrench (for oil fill bolt/cap, if required)
  • Oil drain pan
  • Funnel (preferably flexible or with a small spout)
  • Clean shop towels or rags
  • Latex or nitrile gloves (to keep your hands clean and protected)
  • Replacement crush washer (recommended)
  • Correct type and quantity of oil: High-quality transmission oil; capacity is 1.37 quarts (approx. 1.3 liters) for the 2000 WR360
  • Parts tray or magnetic dish (for hardware)
  • Service stand or suitable stand (to safely hold your dirt bike upright and level)

Preparing the Bike

  • Run the engine for 2-3 minutes to warm the oil. Warm oil flows better and helps suspend contaminants, making drainage more effective.
  • Turn off the engine. Ensure the bike is secure and level on a stand.
  • Clean around the oil fill and drain areas with a towel to prevent dirt from entering the gearbox.

Draining the Oil

  • Locate the gearbox oil drain bolt underneath the right side of the engine case. On the 2000 WR360, it's typically a 6mm Allen bolt on the bottom of the crankcase.
  • Place your drain pan directly underneath. If possible, lay down cardboard or newspaper to catch any drips.
  • With your Allen wrench, carefully remove the drain bolt and let the oil drain completely into the pan. Be careful as the oil may be hot.
  • Inspect the condition of the oil for metal shavings or abnormal discoloration, as this can indicate internal wear.
  • Also inspect the drain bolt and its crush washer. Replace the washer if it appears deformed or damaged to ensure a proper seal and prevent leaks.

Refitting the Drain Bolt

  • Clean the drain bolt thoroughly.
  • If you have a new crush washer, install it now.
  • Thread the bolt back in by hand first to prevent cross-threading, then snug it up with your wrench. Do not overtighten–consult your owner's manual for proper torque specification, but typically it is about 10-15 Nm for Husqvarna two-stroke drain bolts.

Adding New Oil

  • Remove the gearbox oil fill cap (located on the right side of the engine case, just above the clutch cover).
  • Insert your funnel into the fill hole and pour in 1.37 quarts (1.3 liters) of high-quality two-stroke transmission oil. Choose a brand and spec recommended for your riding conditions and compatible with the 2000 WR360.
  • Let the oil settle, then check the oil level if the bike has a sight glass or dipstick. On most WR360s, careful measurement during filling is enough as there may be no dipstick.
  • Replace the oil fill cap and wipe away any spills.

Checking for Leaks and Final Steps

  • Start the engine and let it idle for one minute.
  • Turn off the engine and inspect around the drain bolt and fill cap for leaks.
  • Tighten if necessary but avoid stripping threads.
  • Dispose of the old oil at a certified recycling center. Never pour oil down the drain.
  • Double-check all bolts and the oil level after a short test ride.

Important Model-Specific Call-Outs for the 2000 WR360

  • This bike uses gearbox oil only; the engine is lubricated via premix in the fuel (no engine oil change required).
  • Oil capacity is 1.37 quarts (1.3 liters)–do not overfill, as too much oil can cause clutch drag and foaming.
  • The drain and fill bolts are aluminum–use hand tools and avoid overtightening to prevent stripping threads in the soft engine case.
  • Inspect for contamination in the old oil; coolant or milky appearance can indicate a leaking water pump seal.
  • If you notice excessive metal shavings or blackened oil well before the recommended service interval, inspect internal gears and bearings.
  • While some WR360s feature a sight glass, on many the oil amount must be measured during filling–refer to your owner's manual for verification.
  • Recommended gearbox oil quality is a premium synthetic designed for high-stress two-stroke gearboxes, such as AMSOIL or manufacturer-recommended alternatives.

Conclusion

Changing the gearbox oil on your 2000 Husqvarna WR360 is a straightforward process that can dramatically extend the life of your transmission and improve shifting performance. Follow these steps and tips to keep your bike reliable, ready, and performing at its peak on every ride.

MotoSport.com—your source for everything dirt bike maintenance.

Related Shopping Categories

Shop Motor Oil for a 2000 Husqvarna WR360 Dirt Bike.

Shop Oil Filters for a 2000 Husqvarna WR360 Dirt Bike.

Shop Oil Drain Pans for a 2000 Husqvarna WR360 Dirt Bike.

Shop Tools for a 2000 Husqvarna WR360 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2000 Husqvarna WR360 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.