How to Change the Oil in a 2000 Husaberg FE600

Shop parts for a 2000 Husaberg FE600 Dirt Bike.

Performing regular oil changes on your 2000 Husaberg FE600 is critical for engine longevity and consistent performance. Below is a comprehensive, MotoSport.com proprietary guide to changing the oil on this specific model, with essential tool lists, step-by-step instructions, and model-specific call-outs owners need to know.

Tools and Supplies Needed

  • 8mm socket (1/4 inch drive)
  • 13mm socket (1/2 inch drive)
  • Socket wrench or ratchet
  • Oil drain pan
  • Funnel (for clean pouring)
  • Clean rags or paper towels
  • New engine oil (800 mL, typically 10W-50 or as recommended in your manual)
  • New oil filter (Husaberg OEM recommended)
  • Replacement O-rings and gaskets for the oil filter cover
  • Torque wrench (for proper reassembly)
  • Nitrile gloves (optional, to keep hands clean)

Steps to Change the Oil

  • Warm up the engine:
    • Start the bike and let it run for 3-5 minutes. This helps thin the oil so it drains more thoroughly and removes more contaminants.
  • Prepare your work area:
    • Place the bike upright on a stand.
    • Set up your oil pan beneath the engine's drain plug to catch old oil.
  • Remove the oil drain plug and drain oil:
    • Using a 13mm socket, remove the oil drain plug located at the lowest point on the engine case.
    • Allow oil to thoroughly drain–tilting the bike gently side to side can help remove more old oil.
    • Remove and clean the oil screen attached to the drain plug, wiping away debris and old oil.
  • Remove and replace the oil filter:
    • Locate the oil filter cover, typically held by two 8mm bolts.
    • Unscrew bolts and gently remove the cover, watching for old gaskets or O-rings that may stick to either side.
    • Take out the old filter and any residual gaskets or O-rings.
    • Thoroughly clean cover surfaces and the cavity where the filter sits. Husaberg service documentation stresses cleaning all mating surfaces.
    • Lubricate new O-rings with engine oil before installing them.
    • Insert the new filter and cover, making sure everything is aligned.
    • Tighten the bolts carefully to 5 Nm (do not over-tighten to avoid stripping threads).
  • Inspect and reinstall the oil drain plug:
    • Inspect the drain plug O-ring. Replace if worn or cracked.
    • Reinstall the drain plug and, using a torque wrench, tighten to factory specification (typically 10-15 Nm; confirm in your Owner’s Manual).
  • Refill with new oil:
    • Remove the oil fill cap and use a funnel to pour in 800 mL of recommended engine oil (10W-50 or 10W-40 for most conditions).
    • Keep the bike upright to ensure an accurate fill.
  • Check oil level:
    • Start the engine and let it idle for 2 minutes.
    • Turn off the bike, let it sit for a minute, then check the oil level. Add more oil if needed; do not overfill.
  • Inspect for leaks:
    • Look around the drain bolt and oil filter cover for any signs of leaking oil while the engine runs briefly.
    • Re-torque bolts if leaks are found or replace gaskets/O-rings if necessary.
  • Dispose of oil and old parts responsibly:
    • Bring used oil and filters to an approved recycling facility.

2000 Husaberg FE600 Model Specific Call-outs

  • The FE600 shares its oil system and parts design with the 1999–2000 models. Always use OEM Husaberg filters and seals for best reliability.
  • The oil capacity is 800 mL—using more can cause excessive case pressure, while less risks lubrication failure.
  • Be careful with the filter cover bolts—they are low-torque and the threads can strip easily if overtightened.
  • Regular cleaning of both the oil screen and oil filter cavity is critical, as debris can clog oil flow and starve the engine.
  • If riding in hot climates or racing, oil changes must be performed more frequently (every 10–20 hours) and frequent oil level checks are suggested.

Extra Pro Tips

  • Use a mechanical dirt bike service kit to ensure you have all necessary seals, gaskets, and replacement fluids ready in advance.
  • Record the date and hour meter reading after each oil change for maintenance planning.

Routine maintenance is key to enjoying the high-performance nature of your Husaberg FE600. With the right tools, quality parts, and attention to detail, your engine will reward you with many more miles of adventure.

Related Shopping Categories

Shop Motor Oil for a 2000 Husaberg FE600 Dirt Bike.

Shop Oil Filters for a 2000 Husaberg FE600 Dirt Bike.

Shop Oil Drain Pans for a 2000 Husaberg FE600 Dirt Bike.

Shop Tools for a 2000 Husaberg FE600 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2000 Husaberg FE600 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.