How to Change the Oil in a 1995 Honda CR125

Shop parts for a 1995 Honda CR125 Dirt Bike.

Changing the oil in your 1995 Honda CR125 is a critical maintenance task that keeps your dirt bike's transmission, clutch, and engine performing at their best. This robust step-by-step guide—proprietary to MotoSport.com—details the tools, process, and important model-specific tips to ensure a safe, efficient, and proper oil change.

Tools and Supplies Needed

  • 17mm socket or wrench (for the drain bolt)
  • Oil drain pan
  • Pro Honda HP2 2-stroke oil or equivalent
  • New sealing washer (for the drain bolt; highly recommended)
  • Shop rags (for cleaning any spills)
  • Torque wrench
  • Funnel (for refilling oil)
  • Gloves and safety glasses (for personal protection)
  • Service manual (for reference, if needed)

Model-Specific Callouts: 1995 Honda CR125

  • The 1995 CR125 uses a 17mm drain bolt for the transmission oil.
  • Drain bolt torque spec: 22 ft-lb (30 Nm).
  • Recommended oil quantity: Approximately 0.60 US quarts (0.57 liter) at each change.
  • Always use a new sealing washer to prevent leaks when reinstalling the drain bolt.
  • Warming the engine before draining will help remove more contaminants and ensure a thorough oil change.
  • Proper oil disposal is crucial–never dump old oil; use an approved recycling facility.

Step-By-Step Oil Change Instructions

1. Prepare Your Bike and Work Area

  • Place your CR125 on a level surface, ideally on a bike stand. Make sure it is stable before beginning.
  • Gather all your tools and supplies within reach.
  • Wear gloves and safety glasses.

2. Warm Up the Engine

  • Start the bike and let it idle for 1-2 minutes. This helps the oil flow better, ensuring contaminants are suspended for maximum removal.
  • Turn off the engine and allow it to sit for a minute so components are not dangerously hot but the oil is still warm.

3. Drain the Old Oil

  • Locate the 17mm drain bolt on the bottom of the right side of the crankcase.
  • Place a drain pan underneath the engine.
  • Use your socket or wrench to carefully loosen and remove the drain bolt. Watch for the sealing washer; do not lose it. If it is damaged, replace it immediately.
  • Let all the oil drain completely into the pan (this can take a few minutes).
  • Inspect the old oil for metal shavings, excessive clutch fiber (grayish tint is normal), or other contaminants.

4. Reinstall the Drain Bolt

  • Once the oil has fully drained, clean off the drain bolt and install a new sealing washer.
  • Thread the drain bolt back in by hand to avoid cross-threading.
  • Use a torque wrench to tighten the drain bolt to 22 ft-lb (30 Nm). Do not overtighten as this may strip the threads.

5. Add New Oil

  • Remove the oil filler cap, typically located on the right crankcase cover.
  • Insert a funnel and pour in 0.60 US quarts (0.57 liter) of recommended transmission oil (Pro Honda HP2 2-stroke oil or equivalent).
  • Replace the filler cap securely.

6. Check for Leaks and Verify Oil Level

  • Start the engine and let it run for 30 seconds to circulate the new oil through the transmission.
  • Turn off the engine and inspect the area around the drain bolt for any leaks.
  • Allow the bike to sit for a minute, then check the oil level. Add small amounts if necessary to reach the correct level.

7. Final Steps

  • Wipe up any spilled oil and dispose of the old oil and filter properly–never pour it down the drain.
  • Record the service in your maintenance log; a regular oil change interval helps preserve the life of your CR125‘s transmission and clutch.
  • Reinstall any skid plates or guards if removed for the procedure.

Extra Tips for the 1995 CR125 Owner

  • Inspect the removed oil for debris each time; significant particles can signal emerging transmission or clutch problems.
  • If shifting feels notchy or you see excessive clutch dust (gray color in oil), consider inspecting or replacing clutch plates soon.
  • Never mix oil brands or types within the same change; always use a high-quality, reputable oil designed for 2-stroke transmissions.
  • Store leftover new oil in a sealed container, clearly labeled, for your next change.

Conclusion

With the proper tools and these detailed steps—as well as your attention to crucial model-specific details—you can confidently and quickly change the oil in your 1995 Honda CR125. Regular oil changes using the right methodology will maximize your bike‘s lifespan and performance.

Related Shopping Categories

Shop Motor Oil for a 1995 Honda CR125 Dirt Bike.

Shop Oil Filters for a 1995 Honda CR125 Dirt Bike.

Shop Oil Drain Pans for a 1995 Honda CR125 Dirt Bike.

Shop Tools for a 1995 Honda CR125 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 1995 Honda CR125 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.