How to Change the Coolant in a 2024 GAS GAS EC 300
Regularly changing the coolant in your 2024 GAS GAS EC 300 is essential for maintaining optimal performance & reliability, especially for the demanding conditions most riders face. This two-stroke enduro's high-performance engine and integrated cooling system require attention to detail for a successful coolant change. Below is a robust, step-by-step guide specifically tailored to the GAS GAS EC 300, plus important notes unique to this model.
Preparation – What You Need
- Appropriate coolant (glycol-based, pre-mixed or as specified by GAS GAS)
- Drain pan
- Ratchet set with appropriate sockets
- Flat-blade screwdriver
- Funnel
- Shop rags or towels
- Protective gloves & eye protection
Step-by-Step Coolant Change Procedure
- Ensure the bike is cool and secure: Allow your EC 300 to cool completely before starting this process to prevent injury from hot coolant. Place the bike upright on a stable stand.
- Remove the skid plate (if equipped): For easier access to the drain bolt, remove any underbody protection. This step is optional but recommended.
- Locate the radiator cap and drain bolt: The radiator cap is found on the right side, above the cylinder head. Place your drain pan directly below the water pump cover where the drain bolt is located at the lowest point of the coolant circuit.
- Open the radiator cap: Loosen the cap slowly to release pressure. This helps coolant drain freely.
- Remove the drain bolt: Use your socket to carefully loosen and remove the coolant drain bolt. Allow the old coolant to flow into your drain pan.
- Optional – Drain the left radiator hose: For a more thorough flush, loosen the clamp and slide off the lower radiator hose to release trapped coolant, then reattach and secure the clamp.
- Inspect & clean: Check the drain bolt and sealing washer for wear or damage. Wipe any residue from mating surfaces.
- Reinstall the drain bolt: Ensure the sealing washer is in place and torque the drain bolt to the manufacturer's specification (refer to your service manual for EC 300 specs).
- Refill the system: Using a funnel, pour new coolant into the radiator fill neck. Fill until the coolant reaches the base of the fill opening.
- Bleed air from the cooling system: The EC 300 is equipped with a small bleed screw on the cylinder head. Loosen this bleed screw slightly. Wait for air bubbles to escape and a steady stream of coolant to appear, then retighten the screw securely .
- Re-top off coolant: Check the fill level again and top off if necessary.
- Check & clean up: Reinstall the radiator cap. Start the bike and let it idle for a few minutes. Shut it off, allow it to cool, and recheck the coolant level, adding more if needed.
- Dispose of old coolant properly: Used coolant is hazardous. Bring it to an appropriate recycling or disposal facility.
2024 GAS GAS EC 300 Owner Tips & Notes
- Bleed System Thoroughly: Due to the design of the EC 300 cooling circuit, air pockets can form and cause overheating. Always open the bleed screw during refilling to purge trapped air.
- Coolant Compatibility: Use only non-silicate, motorcycle-specific coolant. Avoid automotive coolant with silicates or additives not recommended by the manufacturer.
- Regular Inspection: The EC 300's high-revving engine can be sensitive to coolant quality and level. Check coolant level and condition before every ride, especially after hard or extended use.
- Gasket Care: If any O-rings or washers are damaged when draining or bleeding, replace them to prevent leaks.
- Interval: GAS GAS recommends changing coolant at least once per year for optimal protection and performance, or more often under race conditions.
Changing the coolant on your 2024 GAS GAS EC 300 is a fundamental maintenance skill that pays dividends in engine life and reliability. Keep your cooling system healthy for worry-free rides season after season.
Related Shopping Categories
Shop Radiator Hoses for Your Ride
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.