How to Change the Coolant in a 2023 Husqvarna FS 450: MotoSport Maintenance Guide
Shop parts for a 2023 Husqvarna FS 450 Dirt Bike.
Keep your 2023 Husqvarna FS 450 delivering peak performance by regularly servicing the cooling system. Coolant protects your engine from overheating, freezing, and internal corrosion. Below is MotoSport's proprietary guide to changing the coolant–including tips unique to this race-focused supermoto and motocross machine.
What You Need
- Fresh coolant formulated for motocross or off-road motorcycles
- Basic hand tools (sockets, screwdrivers)
- Drain pan
- Funnel
- Torque wrench (recommended)
- Safety gloves and goggles
Model-Specific Notes for the 2023 Husqvarna FS 450
- The compact single-cylinder engine in the 2023 FS 450 has closely packed cooling passages–be thorough in draining and ensure no air is trapped when refilling.
- The radiator cap is mounted high for a low center of gravity. Carefully follow the fill and bleed steps for proper coolant level.
- Race-oriented materials mean it's critical to use a coolant compatible with aluminum and magnesium.
Step-by-Step Coolant Change Procedure
- Prepare the motorcycle: Place the bike upright on a stand with the engine completely cool. Remove the radiator shrouds if they block access to the radiator cap.
- Access the drain bolt: Find the coolant drain bolt, typically located at the bottom of the water pump cover on the right side of the engine. Position your drain pan underneath.
- Drain coolant: Slowly loosen the radiator cap to release any built-up pressure, then remove the drain bolt and allow coolant to fully drain. To speed up draining, you can also remove the lower radiator hose (catch all coolant–it is toxic and must be disposed of properly).
- Optional flush: For a thorough service, pour clean, distilled water into the radiator, reattach the drain bolt, run the engine briefly, then drain again. Repeat until the water runs clear. Always reinstall the drain bolt (with the specified torque, if available) after draining.
- Inspect components: Check hoses, hose clamps, and the inside of the radiator cap for signs of wear or corrosion. Replace any compromised parts before proceeding.
- Refill with new coolant:
- Pour new coolant into the radiator up to the base of the filler neck or as marked inside the radiator (do not overfill).
- Find and open the cylinder head bleeder screw (located above the exhaust port) to allow trapped air to escape. Close the screw once only coolant (no bubbles) flows out.
- Top off coolant as needed.
- Reinstall components: Reinstall the radiator cap and any shrouds removed earlier.
- Start and inspect: Run the engine for several minutes at idle. Once cool, recheck radiator level and top off as needed. Inspect for leaks at all connections.
Important Tips for FS 450 Owners
- Bleeding the system is crucial–trapped air can cause overheating and engine damage.
- Never mix different types of coolant. Use coolant compatible with your FS 450's aluminum and magnesium parts.
- Stick to the coolant change interval in your owner's manual for maximum engine protection.
Care and Safety Reminders
- Always perform maintenance with the bike cool to avoid burns.
- Dispose of old coolant responsibly–it is hazardous to people, pets, and the environment.
Stay on top of maintenance and keep your 2023 Husqvarna FS 450 ready for anything with genuine and aftermarket parts from MotoSport.
Related Shopping Categories
Shop Radiators for a 2023 Husqvarna FS 450 Dirt Bike.
Shop Coolant for a 2023 Husqvarna FS 450 Dirt Bike.
Shop Temperature Sensors for a 2023 Husqvarna FS 450 Dirt Bike.
Shop Tools for a 2023 Husqvarna FS 450 Dirt Bike.
Shop Radiator Hoses for a 2023 Husqvarna FS 450 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.