How to Change the Coolant in a 2023 GAS GAS MC 250
The 2023 GAS GAS MC 250 is a high-performance two-stroke dirt bike that relies on a precise cooling system to deliver max power and reliability. Regular coolant changes are key to engine health, especially after hard rides or heavy use. This step-by-step guide covers the complete process for changing the coolant, with unique insights specific to the MC 250.
What Makes the 2023 MC 250 Cooling System Unique?
- Uses a pressurized system with a 1.8 bar (26 psi) radiator cap for improved boiling resistance
- Features easily accessible drain and bleed ports
- Premium aluminum radiators for rugged performance
Note: Only perform maintenance when the engine is cool, as the coolant system is pressurized and can cause burns if opened hot.
Tools & Supplies Needed
- Phillips or flat screwdriver (per radiator shroud type)
- 8mm or 10mm wrench (drain bolt size can vary)
- Catching pan for old coolant
- Fresh coolant (high-quality motorcycle-specific, consult owner manual for type and capacity)
- Clean rags
- Gloves and safety glasses
Step-by-Step Coolant Change Guide
- Prep the Bike
- Let the MC 250 cool completely.
- Clean around the radiator cap and drain area to avoid contamination.
- Stabilize the bike on a level surface or use a stand.
- Remove the Radiator Cap
- Slowly loosen the radiator cap to relieve residual pressure.
- Set the cap aside on a clean surface.
- Drain the Old Coolant
- Locate the coolant drain bolt on the lower engine side cover, typically below the water pump area.
- Place a catch pan under the bike.
- Remove the drain bolt and allow coolant to flow out completely.
- Tip the bike gently side to side if needed to fully empty the system.
- Flush (Optional, but Recommended)
- If desired, pour in a small amount of distilled water and repeat the drain step to remove sediment.
- Do not use tap water as it can introduce minerals and cause corrosion.
- Reinstall the Drain Bolt
- Check the drain bolt O-ring or washer for any wear—replace if necessary.
- Screw back the drain bolt and tighten to the manufacturer's specified torque.
- Fill with Fresh Coolant
- Pour the new coolant into the radiator up to the base of the filler neck.
- The MC 250 has a bleeder screw on or near the cylinder—crack this open slightly while filling to allow trapped air to escape, then close it once coolant flows out smoothly.
- Check for Air Pockets
- Squeeze the radiators or hoses gently to help purge any bubbles.
- Re-check and top off the level as needed.
- Reinstall the Radiator Cap
- Ensure the cap is clean and seals properly before installation.
After the Coolant Change
- Start the bike and let it idle. Watch temperature and coolant level.
- Re-check the coolant level after a brief ride—top up if necessary.
- Inspect for leaks at the drain bolt, radiator cap, and hoses.
- Always dispose of old coolant responsibly; it's toxic to people and animals.
Special Notes for the MC 250 Owner
- The MC 250's pressurized cap helps the bike run cooler, but use only OEM or high-quality replacement caps if a swap is needed.
- Check and carefully clean the radiator fins regularly—a clogged or bent radiator will reduce cooling efficiency.
- If riding in hot conditions or slow terrain, monitor coolant and avoid boiling. Adjust gearing or jetting if repeatedly overheating.
Changing the coolant on your 2023 GAS GAS MC 250 is simple maintenance that safeguards your engine performance and longevity. Regular checks and fresh coolant keep you ready for every MotoSport ride!
Related Shopping Categories
Shop Radiator Hoses for Your Ride
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.