Bleeding the Brakes on a 2025 Africa Twin 1100 Adventure Sports ES DCT

Shop parts for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

The 2025 Honda Africa Twin 1100 Adventure Sports ES DCT is equipped with hydraulic disc brakes front and rear, and ABS is standard. The DCT transmission does not alter the brake bleeding process; the front lever and rear pedal still operate hydraulic circuits that need clean fluid and no trapped air. This guide covers a full flush and bleed at the calipers. If air has entered the ABS unit itself, the bike needs dealer-level equipment, so stop before you open the system if that is a possibility.

When a Brake Bleed Is Due on This Africa Twin

A spongy or soft front lever, a rear pedal that feels longer or less positive than it used to, or a lever that pulls closer to the grip are classic signs that air or old fluid is affecting the system. Dark, cloudy, or contaminated fluid in either reservoir is another reason to bleed. You should also bleed after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or replacing a master cylinder. Brake fluid absorbs moisture over time, which lowers its boiling point and can cause fade under hard or repeated braking. Many riders refresh fluid on a regular schedule even when the brakes still feel normal, because a sealed system can still take on moisture through normal use.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder
  • A catch bottle for old fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make a one-person job easier, but neither is required. Do not use fluid from a container that has been open and sitting; moisture contamination is exactly what you are trying to remove.

Preparation: Stable Bike, Level Reservoir, Protected Surfaces

Support the Africa Twin securely upright on a stand so it cannot tip while you are working. Turn the handlebars until the front master cylinder reservoir sits level before you open it. Cover painted bodywork, plastic panels, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Remove the reservoir cap and diaphragm, then use the syringe or turkey baster to take out most of the old fluid. Leave enough fluid in the bottom so you do not push air into the master cylinder, and keep the reservoir from running dry for the rest of the job.

Front Brake Bleed, Step by Step

  1. Refill the front reservoir with fresh fluid from the sealed container, leaving the correct air space above the fluid as indicated by the reservoir markings.
  2. Slide the clear tubing over the front caliper bleeder and route the other end into the catch bottle, making sure the tube stays submerged or runs downhill without loops that trap fluid.
  3. Squeeze the front lever slowly and hold it against the grip. Do not pump it rapidly; steady pressure moves fluid and air more predictably.
  4. With the lever held, open the bleeder about a quarter turn with the box-end wrench. Fluid and air will move through the tube.
  5. Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the caliper.
  6. Check the reservoir level and top it off with fresh fluid. Repeat the squeeze, hold, open, close, and release sequence until the fluid coming through the tube is clean and free of bubbles.
  7. If your bike has more than one front caliper, bleed each one in turn. Start with the caliper farthest from the master cylinder, then move to the other, topping off the reservoir between calipers.

Keep the reservoir topped off throughout. If it runs low enough to draw air, you will be bleeding the same air out again, and on an ABS-equipped bike you may push air into a place that is harder to clear.

Rear Brake Bleed on the Africa Twin

  1. Open the rear master cylinder reservoir, remove most of the old fluid, and refill with fresh fluid of the type marked on the cap.
  2. Attach the clear tubing to the rear caliper bleeder and route it into the catch bottle.
  3. Press and hold the rear brake pedal. Keep steady pressure on it.
  4. Open the rear bleeder about a quarter turn, let fluid and air pass, then close the bleeder before releasing the pedal.
  5. Top off the rear reservoir and repeat until the fluid is clean and bubble-free. Check the reservoir after every few cycles so it never runs dry.
  6. When the fluid looks clean, close the bleeder snugly and move on to the finish checks.

The rear circuit is smaller and can empty quickly, so watch the reservoir closely. If the pedal goes to the bottom with no resistance, stop and check for a leak or a reservoir that has run dry before continuing.

Finishing, Testing, and Knowing When to Stop

Tighten the bleeder snugly without overtightening; you want it sealed, not distorted. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the caliper, master cylinder, and bodywork. Check for leaks at the bleeder and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.

If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and diagnose the problem. Because this Africa Twin has ABS, air that has entered the ABS unit after a reservoir run dry or after lines were disconnected may require a dealer-level procedure or diagnostic tool. A lever that never becomes firm is not a brake system you should ride on; have the bike inspected before you head out.

Related Shopping Categories

Shop Brake Fluid for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Lines for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Pads for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Stands for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Tools for a 2025 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.