Bleeding the Brakes on a 2024 Honda Africa Twin 1100
Shop parts for a 2024 Honda Africa Twin 1100 Motorcycle.
What You Are Working With
The 2024 Honda Africa Twin 1100 uses hydraulic disc brakes at both ends, and ABS is part of the package. That is good news for a DIY bleed: you can refresh fluid and remove air through the caliper bleeders in the usual way, using the front brake lever and the rear brake pedal to push fluid through the system. What you should not do is treat the ABS modulator as a home-service bleed point. A normal bleed at the calipers is the right approach for routine fluid replacement and for air that entered at a caliper or line fitting. If the reservoir has run dry, or if the ABS unit or its lines have been disconnected, air may be trapped inside the ABS hardware, and that is a job for a shop with the correct diagnostic equipment.
Because this is a safety-critical system, work slowly and keep the reservoir from running low. The goal is not just to see new fluid in the tube; it is to end with a firm lever, a firm pedal, and no air anywhere in the hydraulic circuit.
When a Bleed Is Due
Bleed the brakes when the lever or pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in the reservoir looks dark or cloudy. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard use, so many riders refresh the fluid on a regular schedule as preventive maintenance.
- A soft or spongy front lever or rear pedal
- A lever that slowly sinks under steady pressure
- Dark, cloudy, or contaminated-looking fluid in the reservoir
- Recent line, caliper, or master cylinder service
- Routine fluid refresh before a long trip or hard-riding season
Tools and Supplies to Stage First
Gather everything before you open the reservoir so you are not searching for a tool with the system exposed. Use fresh brake fluid of the type marked on the master cylinder reservoir cap, and use fluid from a sealed container. Do not substitute a different fluid type based on guesswork.
- Fresh brake fluid of the type marked on the reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the manual lever-and-bleeder method works fine if you are careful about closing the bleeder before releasing the lever or pedal.
Preparation Before You Open the System
Support the Africa Twin securely upright on a stand. Turn the handlebars so the front master cylinder reservoir sits level before you remove the cap. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Clean the area around the reservoir cap before opening it so dirt does not fall into the fluid. Have the catch bottle positioned below the caliper bleeder and route the clear tube so it stays put while you work the lever or pedal.
Step-by-Step Bleeding Procedure
- Open the front reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap later.
- Attach the clear tube to the front caliper bleeder and route the other end into the catch bottle.
- Fit the box-end wrench onto the bleeder. Squeeze and hold the front brake lever.
- Open the bleeder about a quarter turn to let fluid and air escape. Close the bleeder before releasing the lever.
- Release the lever, then repeat the squeeze-hold-open-close-release sequence. Keep topping off the reservoir so it never draws air.
- Continue until fresh, clean fluid comes through the tube with no bubbles. If your bike has more than one front caliper, bleed each caliper in turn, one at a time. As a general habit, start with the caliper farthest from the master cylinder when the layout gives you a clear choice.
- Move to the rear brake. Attach the tube to the rear caliper bleeder, press and hold the pedal, open the bleeder about a quarter turn, then close it before releasing the pedal.
- Repeat the rear sequence until the fluid runs clean and bubble-free, topping off the rear reservoir as needed.
- Check the reservoir level again at both ends before you close anything up.
Finishing, Leak Checks, and Test Ride
Tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the caliper, reservoir, and surrounding surfaces. Check for leaks at the bleeder and at the banjo fittings.
Before riding, the lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.
If the Lever or Pedal Will Not Firm Up
If the lever will not firm up after several bleeding attempts, if it firms only after pumping, or if bubbles keep appearing, stop and diagnose rather than continuing to pump fluid through. Persistent air can come from a fitting that is not sealing, a bleeder that is not closing fully, or fluid leaking at the master cylinder or caliper. Any situation where air may have entered the ABS unit—especially after the reservoir ran dry or the ABS hardware was disturbed—should go to a shop. A firm, consistent lever and pedal are the confirmation that the job is complete.
Related Shopping Categories
Shop Brake Fluid for a 2024 Honda Africa Twin 1100 Motorcycle.
Shop Brake Lines for a 2024 Honda Africa Twin 1100 Motorcycle.
Shop Brake Pads for a 2024 Honda Africa Twin 1100 Motorcycle.
Shop Stands for a 2024 Honda Africa Twin 1100 Motorcycle.
Shop Brake Tools for a 2024 Honda Africa Twin 1100 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.