Bleeding the Brakes on Your 2024 Honda Africa Twin 1100 DCT

Shop parts for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

The 2024 Honda Africa Twin 1100 DCT uses hydraulic disc brakes at both ends and is equipped with ABS. The DCT transmission does not change how the brake hydraulics are serviced, so the job is familiar: remove old fluid, push fresh fluid through the system, and expel air until the lever and pedal feel firm. Because this is a safety-critical system, work methodically and stop if anything feels unusual. The front and rear circuits are bled separately on this model.

Why Bleeding Matters on This Africa Twin

Brake fluid absorbs moisture over time, even in a sealed system. That moisture lowers the fluid’s boiling point, which can cause fade under hard or repeated braking, and it can darken the fluid in the reservoir. Air is the more immediate problem: a spongy lever, a pedal that feels soft, or a lever that pulls closer to the grip than it used to often means air has entered the system. Bleeding is also necessary after work that opened the hydraulics, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Many riders refresh brake fluid on a regular schedule even when the brakes feel normal, because clean fluid is cheap insurance against fade and corrosion.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder valve
  • A catch bottle for used fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier

Preparation and Paint Protection

Support the bike securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastic bodywork, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them aside where they will not pick up grit. Work in a well-ventilated area and keep fresh fluid closed until you are ready to pour.

Bleeding the Front and Rear Brakes

Use this sequence for the front circuit first, then repeat the same logic at the rear. If your front setup has more than one caliper, bleed one caliper at a time; a common approach is to start with the caliper farthest from the master cylinder, then do the other. Never let the reservoir run dry during any of this, or you will pull air back into the system.

  1. Open the front reservoir and use the syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the bottom so you do not introduce air through the master cylinder.
  2. Refill the reservoir with fresh fluid from the sealed container, keeping it below the top edge so it does not overflow when the diaphragm goes back in.
  3. Attach the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around the bleeder.
  4. Squeeze the front lever slowly and hold it. With the lever held, open the bleeder about a quarter turn and let fluid and air escape through the tube.
  5. Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the caliper.
  6. Repeat the squeeze, hold, open, close, and release sequence until the fluid coming through the tube is fresh, clean, and free of bubbles. Check the reservoir often and top it off before it gets low.
  7. If the front has a second caliper, move the tubing and wrench to that caliper and repeat the same process. Keep the reservoir topped off throughout.
  8. When the front is done, close the bleeder snugly without overtightening it, remove the tubing, and wipe the caliper area clean.
  9. Move to the rear brake. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid.
  10. Attach the clear tubing to the rear caliper bleeder and route it into the catch bottle. Press and hold the rear pedal, open the bleeder about a quarter turn, then close it before releasing the pedal.
  11. Continue the press, hold, open, close, and release sequence until the rear fluid runs clean and bubble-free. Top off the rear reservoir as needed so it never runs dry.
  12. Close the rear bleeder snugly, remove the tubing, and clean any fluid from the caliper and surrounding parts.

Finishing the Job and Checking for Leaks

With both circuits bled, fill each reservoir to the correct level marking. Reinstall the diaphragm and cap carefully so the seal sits flat and the cap threads are not cross-threaded. Wipe down the master cylinders, calipers, and bleeders with a clean rag, then rinse any area where fluid may have dripped. Check for leaks at the bleeder valves and at the banjo fittings where the brake lines attach. A small weep at a bleeder usually means it is not snug; tighten it gently and recheck. Do not overtighten, because damaged bleeder seats can leak or break.

Test Before You Ride

The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. With the bike upright and in a safe area, test the brakes at low speed before riding normally. If either brake feels different from one pull to the next, or if the lever firms up only after several pumps, there is still air in the system and it needs more attention.

Troubleshooting and When to Take It to a Shop

If the lever or pedal will not firm up after several careful bleeding attempts, stop and reassess. Persistent bubbles, fluid leaking from the master cylinder or caliper, or a lever that only feels good after pumping all point to a problem that may be beyond a simple flush. Because this Africa Twin has ABS, air that has entered the ABS unit itself—for example, if a reservoir ran dry or the ABS unit or its lines were disconnected—may require a dealer-level procedure or diagnostic tool. Do not try to guess an ABS bleed sequence at home. If you are unsure whether air is trapped in the ABS unit, or if the brakes still feel soft after a thorough bleed, have the bike inspected by a qualified shop before riding.

Related Shopping Categories

Shop Brake Fluid for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Lines for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Pads for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

Shop Stands for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Tools for a 2024 Honda Africa Twin 1100 DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.