Bleeding the Brakes on a 2024 Ducati Multistrada V4 S Grand Tour

Shop parts for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Your 2024 Ducati Multistrada V4 S Grand Tour has hydraulic disc brakes front and rear, and it is equipped with ABS. The front lever and rear pedal each push fluid through a sealed circuit to apply the calipers, with the ABS unit integrated into that circuit. Bleeding pushes fresh fluid through the system while expelling trapped air. It is also the right time to flush out old fluid, which absorbs moisture over time. Because brakes are safety-critical, work methodically and stop if anything feels unclear.

When a Bleed Is Needed — and Why Old Fluid Matters

A spongy lever, a pedal that feels soft, or a lever that pulls closer to the grip than it used to are classic signs of air in the system. Dark or cloudy fluid in the reservoir is another cue. Bleeding is also required after any work that opened the hydraulic system, such as new lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture from the air over time. That lowers its boiling point and can lead to brake fade under hard use, so many riders refresh it on a regular schedule.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • Clear tubing that fits tightly over the bleeder nipple, plus a catch bottle.
  • Rags or shop towels, and a syringe or turkey baster for removing old fluid from the reservoir.
  • The correct driver for the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder to simplify one-person work.

Preparation: Stable Bike, Level Reservoir, Protected Surfaces

Support the Multistrada securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. Wipe up any spill immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them where they will not pick up grit.

Step-by-Step Bleeding Procedure

Work on one hydraulic circuit at a time. The front lever operates the front calipers, and the rear pedal operates the rear caliper. A general practice is to start with the caliper farthest from its master cylinder, but you can complete the front circuit and then the rear, or the reverse, as long as you finish each circuit fully.

  1. Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir. Do not let the reservoir run dry at any point.
  2. Refill the reservoir with fresh fluid to the upper level marking. Keep the cap and diaphragm nearby, but do not seal the reservoir yet.
  3. Fit the box-end wrench over the bleeder valve, then push the clear tubing onto the bleeder nipple and route the other end into the catch bottle. The tube should fit snugly so air cannot be drawn in around it.
  4. Squeeze the front lever, or press the rear pedal, several times and then hold it firm. Do not release it while the bleeder is open.
  5. Open the bleeder about a quarter turn. Fluid and any trapped air will flow through the tube. Watch the tube and the reservoir level.
  6. Close the bleeder before releasing the lever or pedal. This order matters: releasing first can pull air back into the caliper.
  7. Repeat the pump-hold-open-close cycle. Top off the reservoir as the level drops so it never draws air. Continue until the fluid in the tube runs clean and free of bubbles.
  8. Bleed each front caliper in turn using the same cycle. Finish one caliper completely before moving to the other.
  9. For the rear, repeat the same sequence at the rear caliper bleeder using the pedal. Keep the rear reservoir topped off throughout.

Finishing Up: Tighten, Fill, Clean, and Inspect

When clean, bubble-free fluid comes through, close the bleeder snugly with the box-end wrench. Do not overtighten; snug is enough to seal. Fill the reservoir to the correct level marking with fresh fluid. Reinstall the diaphragm and cap. Wipe any spilled fluid from the caliper, bleeder, reservoir, and surrounding surfaces, and rinse with water if needed. Check for leaks at the bleeder and at the banjo fittings. A weep at the bleeder means it is not seated; a weep at a banjo fitting means that connection needs attention before riding.

Testing Before You Ride

Pull the front lever and press the rear pedal. Each should feel firm and consistent, not spongy. Hold steady pressure for several seconds; the lever or pedal should not slowly sink. Spin each wheel and check for drag; the brakes should release cleanly. Then test at low speed in a safe area, using both brakes gently before riding normally. If anything feels soft or inconsistent, do not ride — recheck the bleed or seek help.

Troubleshooting and When to Take It to a Shop

If the lever will not firm up after several bleeding attempts, or if it firms only after pumping, air is still in the system or is being drawn in. Check that the bleeder is closed before the lever is released, that the tube fits tightly, and that the reservoir never ran dry. Persistent bubbles can also mean a loose bleeder or a fitting that needs attention. Fluid leaking from the master cylinder or caliper is a stop sign; have it inspected.

Because your Multistrada V4 S Grand Tour has ABS, there is one more boundary to respect. A standard bleed through the caliper bleeders is generally used to refresh fluid. But if air has entered the ABS unit itself — for example, if the reservoir ran dry, or the ABS unit or its lines were disconnected — the system may require a dealer-level procedure or diagnostic tool. Do not improvise an ABS bleed. If you are not confident, or if the lever still will not firm up after careful work, take the bike to a shop.

Related Shopping Categories

Shop Brake Fluid for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Shop Brake Lines for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Shop Brake Pads for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Shop Stands for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Shop Brake Tools for a 2024 Ducati Multistrada V4 S Grand Tour Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.