Bleeding the Brakes on a 2023 Honda Africa Twin 1100

Shop parts for a 2023 Honda Africa Twin 1100 Motorcycle.

First, Understand the Brake Layout You Are Working On

The 2023 Honda Africa Twin 1100, sold as the CRF1100L, uses hydraulic disc brakes at both ends of the bike, and ABS is part of the package. Up front you have two calipers gripping a pair of discs, fed by a master cylinder at the lever. Out back, a single caliper and disc are fed by a master cylinder at the pedal. Because both circuits are hydraulic, both can be bled in your own garage with hand tools.

The ABS part matters. For routine fluid refreshment—the kind of bleed you do because the fluid is old or the lever feels soft—a normal bleed through the caliper bleeder valves is all that is required. The trouble starts when air gets inside the ABS modulator itself. That can happen if the reservoir ran dry while you were working, if a line was disconnected, or if the ABS unit was removed. In that case the modulator may need a dealer-level procedure or a diagnostic tool to cycle the pump and push the trapped air out. Do not try to improvise that at home; if you suspect air is in the ABS unit, stop and take the bike to a shop.

How to Tell the Brakes Need Bleeding

The most obvious clue is feel. A lever that squishes toward the grip, a lever that now travels noticeably farther than it used to, or a rear pedal that feels long and vague all point to air or degraded fluid in the system. Pull the reservoir cap and look at the fluid: fresh fluid is clear and light, while fluid that has been in service for years turns dark, cloudy, or tea-colored.

Any job that opened the hydraulic circuit is an automatic trigger for a bleed. New brake lines, a caliper rebuild, a master cylinder service, or a line that was cracked loose for any reason all let air in. Beyond symptoms, brake fluid absorbs moisture from the air over time, and that moisture lowers the fluid's boiling point. Under hard, repeated braking—exactly the kind of use an Africa Twin sees on a mountain pass—that can show up as fade. Many riders simply refresh the fluid on a regular interval rather than waiting for a problem to appear.

Tools and Supplies to Gather

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder nipple.
  • A small catch bottle for the old fluid.
  • Rags or shop towels, plus something to drape over painted and plastic surfaces.
  • A syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job easier.

Setting Up Before You Open Anything

Get the bike held securely upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebars until the front reservoir sits level, because an angled reservoir will spill as soon as the cap comes off. Then cover the tank area, the plastics, the instrument cluster, and anything else below the reservoir with rags.

This step is not optional. Brake fluid attacks paint and many plastics on contact, and a single drip left sitting will leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water rather than waiting until the job is finished.

The Bleeding Procedure, Step by Step

  1. Remove the reservoir cap and the diaphragm beneath it, and set them down somewhere clean where they will not pick up grit.
  2. Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave a little at the bottom so you do not introduce air through the master cylinder port.
  3. Refill with fresh fluid from the sealed container, filling to just below the upper level marking.
  4. Slip the box-end wrench over the bleeder valve, then push the clear tubing onto the nipple and route the other end into the catch bottle. A little fluid in the bottle keeps the tube end submerged.
  5. Squeeze the front lever slowly and hold it against the grip. On the rear, press and hold the pedal.
  6. With the lever or pedal held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube.
  7. Close the bleeder before you release the lever or pedal. This is the single most important habit in the whole job—releasing first will suck air back in through the bleeder.
  8. Release the lever or pedal slowly and let it return on its own.
  9. Repeat the squeeze, hold, open, close, release cycle. Check the reservoir every few cycles and top it off, because letting it run dry pulls air straight into the system and undoes your work.
  10. Watch the tubing as you go. You are finished with that bleeder when the fluid coming through has changed from dark to clean and runs free of bubbles.
  11. Move to the other front caliper and repeat the entire process. As a general practice, start with the caliper farthest from the master cylinder in line length and work toward the closest.
  12. Bleed the rear circuit the same way using the pedal, holding pressure while the bleeder is open and closing it before you let the pedal up.

Closing Everything Up

Once clean, bubble-free fluid is coming through, tighten each bleeder snugly with the box-end wrench. Snug is the goal—do not lean on it, because overtightening can damage the valve seat. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and calipers for any sign of weeping or dampness.

Confirming the Job Before You Ride

Pull the lever and press the pedal. Both should feel firm and consistent, and neither should creep slowly toward the grip or the floor under steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If anything feels off at that point, do not ride the bike.

When to Hand It Over to a Shop

If the lever will not firm up after several rounds of bleeding, if it only firms up when you pump it, or if bubbles keep appearing no matter how long you work, something else is wrong—often a worn master cylinder seal or a pinhole in a line. Fluid weeping from the master cylinder or a caliper is another stop sign. And if there is any chance air reached the ABS modulator, let a dealer with the right diagnostic equipment handle it. Brakes are not the system to gamble on.

Related Shopping Categories

Shop Brake Fluid for a 2023 Honda Africa Twin 1100 Motorcycle.

Shop Brake Lines for a 2023 Honda Africa Twin 1100 Motorcycle.

Shop Brake Pads for a 2023 Honda Africa Twin 1100 Motorcycle.

Shop Stands for a 2023 Honda Africa Twin 1100 Motorcycle.

Shop Brake Tools for a 2023 Honda Africa Twin 1100 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.