Bleeding the Brakes on Your 2023 Honda Africa Twin 1100 Adventure Sports ES
Shop parts for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
The 2023 Honda Africa Twin 1100 Adventure Sports ES stops on hydraulic disc brakes at both ends, with an ABS system monitoring both circuits. That layout is good news for a home mechanic: the front lever and the rear pedal each have their own master cylinder, reservoir, and caliper bleed point, so a full fluid flush and air bleed is a methodical, achievable job. What follows is a complete walkthrough for this bike — what to gather, how to set it up, how to bleed each circuit, and how to prove the work is done before you ride.
Why and When the Africa Twin's Brakes Need Bleeding
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That moisture lowers the fluid's boiling point, and fluid that boils under hard, repeated braking creates vapor in the lines — which feels exactly like air, because functionally it is. On a tall adventure bike that gets loaded with luggage and ridden two-up, that lost margin matters.
Bleed when the lever or pedal feels spongy, when the lever creeps closer to the grip than it used to, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic system: new lines, caliper service, master cylinder work, or a reservoir that ran dry. Plenty of riders also refresh the fluid on a regular interval as preventive maintenance, since a system can feel fine right up until the day it doesn't.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so skip the bottle that's been sitting on the shelf.
- A box-end wrench that fits the bleeder valve snugly.
- Clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to route it into.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job easier.
Setting Up and Protecting the Bike
Get the bike secure and upright on a stand before you open anything. For the front circuit, turn the handlebar so the reservoir on the master cylinder sits level — a tilted reservoir spills. Check that the rear reservoir is level as well.
Brake fluid attacks paint and many plastics on contact, so drape rags over the tank area, the plastics around the bars, the instrument cluster, and anything below the calipers. If a drop lands on a painted surface, wipe it immediately and rinse the area with water.
Bleeding the Front Brake Circuit
- Wipe the reservoir lid clean, remove the cap and diaphragm, and use the syringe to draw most of the old fluid out.
- Refill with fresh fluid to a safe level, leaving room to top off as you work.
- Push the clear tubing onto the caliper bleeder and run the other end into the catch bottle, positioned so you can watch the tube.
- Squeeze the lever and hold it firm.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Keep an eye on the reservoir level.
- Close the bleeder before you release the lever. Releasing with the bleeder open pulls air back in through the nipple.
- Repeat squeeze, hold, open, close, release until the fluid coming through the tube runs clean and bubble-free.
- Top off the reservoir throughout so it never drops low enough to draw air into the master cylinder.
- If your bike has two front calipers, bleed each one in turn, starting with the caliper farthest from the master cylinder.
Bleeding the Rear Brake Circuit
- Clean the rear reservoir, open it, and remove most of the old fluid with the syringe.
- Refill with fresh fluid and keep the level up as you go.
- Fit the tubing over the rear caliper bleeder and into the catch bottle.
- Press and hold the pedal, open the bleeder a quarter turn, let fluid and air escape, then close the bleeder before releasing the pedal.
- Repeat until the fluid runs clean and clear of bubbles, checking the reservoir level every few cycles.
Finishing Up and Checking for Leaks
When both circuits run clean, close the bleeders snugly — firm enough to seal, without overtightening and damaging the seat. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe away any fluid residue. Then look closely at the bleeder nipples and the banjo fittings at the master cylinder and calipers for weeping or wetness, and pump the lever and pedal a few times to pressurize the system before checking again.
Testing Before You Ride
The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking while you hold them. Spin each wheel and confirm it turns freely — a dragging brake means something is wrong. Then ride slowly in a safe, open area and test the brakes at low speed before riding normally.
When This Job Belongs in a Shop
If the lever won't firm up after several rounds of bleeding, if it only firms up after pumping, if bubbles keep appearing, or if you see fluid at the master cylinder or caliper, stop and get the bike looked at. The same goes for any situation where air may have entered the ABS unit itself — a reservoir that ran dry, or lines or the ABS unit that were disconnected. Clearing air from an ABS modulator generally requires a dealer-level procedure or diagnostic tool, and it isn't something to improvise in a home garage.
Related Shopping Categories
Shop Brake Fluid for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Lines for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Pads for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Stands for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Tools for a 2023 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.