Bleeding the Brakes on a 2022 Honda Africa Twin 1100
Shop parts for a 2022 Honda Africa Twin 1100 Motorcycle.
Start With the Africa Twin’s Brake Layout
The 2022 Honda Africa Twin CRF1100L uses hydraulic disc brakes at both ends, and ABS is part of the package. Each brake has its own master cylinder, its own lines, and its own caliper, so the front lever and the rear pedal are two separate circuits that each need attention. The front brake does most of the stopping on a bike this size, but a soft rear pedal shows up quickly on a loaded descent or a slow-speed maneuver, so plan on bleeding both ends rather than just the front.
Because this bike has ABS, one caveat matters more than anything else in this article. A routine flush through the caliper bleeders is a normal home-garage job and is exactly what this procedure covers. But if air has been allowed into the ABS modulator itself — the reservoir ran dry while you were working, a line was disconnected, or the unit was removed — the system may need a dealer-level procedure or diagnostic tool to purge correctly. If any of that applies, stop here and take the bike to a shop. Do not attempt to force air out of the ABS unit by pumping the lever.
When a Bleed Is Actually Needed
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That moisture lowers the fluid’s boiling point, and a boiling fluid creates vapor in the lines — which feels exactly like air in the system and can cause the lever to go long or soft under hard, repeated braking. That is why many riders refresh the fluid on a regular interval even when nothing feels wrong.
Bleed the brakes sooner if you notice any of the following:
- A spongy or soft lever, or a lever that pulls closer to the grip than it used to
- A rear pedal with more travel or less resistance than before
- Fluid in the reservoir that looks dark, cloudy, or contaminated
- Any recent work that opened the hydraulic system — new lines, caliper service, or master cylinder work
- A lever that firms up only after two or three quick pumps
Tools and Supplies to Have Ready
Gather everything before you open a reservoir, because once the cap is off you do not want to be hunting for a wrench with the system exposed.
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve snugly
- A length of clear tubing that fits tightly over the bleeder nipple
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much easier
Set Up Before You Open Anything
Get the bike securely upright on a stand so it cannot tip while you are working. Turn the handlebars until the front reservoir sits level — on a tall adventure bike the reservoir is angled, and an unlevel reservoir will spill. Then drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir. Brake fluid damages paint and plastic on contact, so wipe up any drip immediately and rinse the area with water if it reaches a painted surface.
The Bleeding Procedure, Step by Step
- Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but leave enough at the bottom that you are not pulling air into the master cylinder port.
- Refill the reservoir with fresh fluid from the sealed container. Keep the cap and diaphragm nearby but off for now.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward slightly before dropping — this helps you see bubbles.
- If your bike has two front calipers, work on one caliper at a time and finish it completely before moving to the other. As a general practice, start with the caliper farthest from the master cylinder.
- Squeeze the lever (or press the pedal) and hold steady pressure on it.
- With pressure held, open the bleeder about a quarter turn. Fluid and air will push out through the tubing. Watch the reservoir level as you do this.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air back into the caliper, which is the single most common mistake in this job.
- Release the lever, then repeat the squeeze–hold–open–close–release cycle. Top off the reservoir every few cycles so it never runs low enough to pull air in.
- Continue until the fluid coming through the tubing is clean and free of bubbles, and the lever feels firm. Then move to the rear circuit and repeat the same sequence at the rear caliper.
Finishing Up and Checking Your Work
Close the bleeder snugly with the box-end wrench — firm enough that it will not weep, but not so tight that you risk damaging the seat. Pull the tubing off and wipe the caliper clean. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for any sign of weeping or a wet film.
Test Before You Ride
With the bike still on the stand, squeeze the lever and hold steady pressure for a slow count of ten. It should feel firm and consistent and should not creep toward the grip. Do the same with the rear pedal. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally — a short, gentle stop first, then a firmer one.
When to Stop and Take It to a Shop
If the lever will not firm up after several full bleeding cycles, if it only firms after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid leaking from the master cylinder or a caliper, stop and have the bike inspected. The same applies if there is any chance air entered the ABS unit. A brake system that is not right is not a system to ride on.
Related Shopping Categories
Shop Brake Fluid for a 2022 Honda Africa Twin 1100 Motorcycle.
Shop Brake Lines for a 2022 Honda Africa Twin 1100 Motorcycle.
Shop Brake Pads for a 2022 Honda Africa Twin 1100 Motorcycle.
Shop Stands for a 2022 Honda Africa Twin 1100 Motorcycle.
Shop Brake Tools for a 2022 Honda Africa Twin 1100 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.