Bleeding the Brakes on a 2022 Honda Africa Twin 1100 DCT

Shop parts for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

What You Are Working With on This Africa Twin

The 2022 Africa Twin 1100 DCT runs hydraulic disc brakes at both ends, and ABS is part of the package. That gives you two completely separate hydraulic circuits to service: a front circuit fed by the master cylinder on the handlebar, and a rear circuit fed by its own master cylinder down by the pedal. Each has its own reservoir, its own bleeder at the caliper, and its own lever or pedal feel to judge when you are done. The DCT gearbox has no bearing on any of this — the brake hydraulics are conventional, and the left-hand control area is not part of the job. Leave the clutch hydraulics alone while you are working on the brakes.

Because this bike carries ABS, a routine fluid refresh through the caliper bleeders is a normal garage task. What is not a garage task is purging air that has found its way into the ABS modulator itself. If the reservoir ever ran dry, if a line or the unit was disconnected, or if the system was opened for service, the pump may need to be cycled with a dealer-level procedure or diagnostic tool before the air will move. If any of that applies, stop and take the bike to a shop.

When a Bleed Is Actually Needed

Lever and pedal feel tell you the most. A front lever that feels spongy, pulls noticeably closer to the grip than it used to, or slowly sinks while you hold steady pressure is asking for attention. The same goes for a rear pedal that feels vague or travels further than normal. Pop the reservoir cap and look at the fluid: dark, cloudy, or contaminated fluid is past its useful life even if the brakes still feel acceptable.

Any job that opened the hydraulic system — new lines, caliper service, master cylinder work — means air got in and a bleed is mandatory afterward. Beyond symptoms, brake fluid absorbs moisture from the air over time, which lowers its boiling point and can bring on fade during hard or repeated braking. Many riders simply refresh the fluid on a regular interval as preventive maintenance rather than waiting for a soft lever.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • Clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much easier

Setting Up Before You Open Anything

Get the bike secure and upright on a stand so it cannot tip while you are leaning on the lever. For the front circuit, turn the handlebars until the reservoir on the bar sits level; a tilted reservoir will spill the moment the cap comes off. Lay rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir, because brake fluid attacks paint and plastic on contact. If a drop does land somewhere it should not, wipe it up immediately and rinse the area with water. Keep the catch bottle low and the tubing routed so fluid cannot run back toward the caliper or drip onto the tire.

Bleeding the Front Brake

  1. Clean the reservoir cap and surrounding area, then remove the cap and the diaphragm.
  2. Draw most of the old fluid out of the reservoir with the syringe, but leave enough to cover the port at the bottom. Never let the reservoir run dry.
  3. Top up with fresh fluid from the sealed container.
  4. Slide the box-end wrench over the bleeder, then push the clear tubing onto the nipple and route the other end into the catch bottle.
  5. Squeeze the front lever slowly and hold it against the grip.
  6. Open the bleeder about a quarter turn. Fluid and air will push out through the tubing.
  7. Close the bleeder fully before you release the lever. Releasing with the bleeder open draws air straight back in.
  8. Release the lever slowly and let it return.
  9. Check the reservoir and top it off, then repeat the squeeze, open, close, release cycle.
  10. Keep going until the fluid coming through the tubing is clean and free of bubbles. If your bike carries two front calipers, bleed one at a time, then run a final pass on the first one. A good general habit is to start with the caliper farthest from the master cylinder.

Bleeding the Rear Brake

  1. Clean and open the rear reservoir, then remove most of the old fluid without exposing the bottom port.
  2. Refill with fresh fluid and fit the wrench and tubing to the rear bleeder.
  3. Press and hold the pedal, open the bleeder a quarter turn, then close it before releasing the pedal.
  4. Release the pedal, top off the reservoir, and repeat until the fluid runs clean and bubble-free.

Finishing the Job Correctly

Once the fluid runs clear at both ends, tighten each bleeder snugly. Snug is the goal — do not lean on it, because overtightening can damage the seat. Bring the reservoir up to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Rinse any spill area with water. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for weeping, and check the reservoir seams as well.

Testing Before You Ride

The lever and pedal should feel firm and consistent, and neither should creep toward the end of its travel while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If anything feels soft or inconsistent, do not ride — go back and bleed again.

Troubleshooting and When to Stop

A lever that will not firm up after several rounds, a lever that only firms up after pumping, or a steady stream of bubbles that never ends usually points to air entering somewhere it should not, such as a loose bleeder, a worn banjo washer, or a failing master cylinder seal. Fluid weeping from the master cylinder or caliper is a repair, not a bleed. And if there is any chance air reached the ABS unit, let a shop cycle the system properly rather than chasing it in the garage.

Related Shopping Categories

Shop Brake Fluid for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Lines for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Pads for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

Shop Stands for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Tools for a 2022 Honda Africa Twin 1100 DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.