Bleeding the Brakes on a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT
Shop parts for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.Know the System Before You Open It
Your 2022 Africa Twin 1100 Adventure Sports ES DCT stops on hydraulic disc brakes at both ends, and ABS is part of the package. That gives you two completely separate hydraulic circuits to service — front and rear — each with its own master cylinder, reservoir, and caliper assembly. Nothing about the DCT gearbox changes how the brakes bleed, but the layout does mean you should plan on working through both circuits rather than just the front.
Because this bike carries an ABS modulator, there is an important line to draw. A routine flush, where you push fresh fluid down through the calipers and out the bleeders, is well within reach of a home mechanic. Air that has migrated into the ABS unit is a different story. If the reservoir has ever been allowed to run dry, or if the ABS unit or its hard lines have been removed or replaced, the modulator may need a dealer-level procedure or diagnostic tool to purge correctly. In that situation, stop and book the bike in.
One more layout note: if your bike is fitted with a secondary rear brake lever on the left handlebar, it feeds the same rear circuit as the foot pedal. It does not create an extra bleed point, so you can ignore it while bleeding and simply use the pedal.
Signs It's Time, and Why It Matters
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and on a heavy adventure bike loaded with luggage and a passenger, a long descent can heat the calipers enough to boil contaminated fluid and give you a lever that goes soft right when you need it most. That is why many riders refresh the fluid on a schedule even when nothing feels wrong.
Watch for a lever or pedal that feels spongy rather than solid, a lever that now comes noticeably closer to the grip than it used to, a pedal with a long dead zone at the top of its travel, or fluid in either reservoir that looks dark, cloudy, or gritty. Bleeding is also mandatory after any work that opened the system: new brake lines, a caliper rebuild or replacement, or master cylinder service.
What to Have on the Bench
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — once a container is opened, it starts absorbing moisture, so use new stock
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing sized to grip the bleeder tightly, plus a catch bottle to hang it in
- Rags or shop towels, and a spray bottle of water for rinsing spills
- A syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional but genuinely helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo job far less fiddly
Setting Up the Bike and Protecting the Finish
Get the Africa Twin secure on a stand so it cannot tip while you are leaning on the bars. Turn the handlebar until the front reservoir sits level, because a tilted reservoir will spill the moment you crack the cap. Before you touch anything, drape rags over the tank area, the plastics, the instrument cluster, and the front fender. Brake fluid attacks paint and many plastics on contact, and the damage is permanent. If a drop lands anywhere it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until you finish.
Bleeding the Front Circuit
- Clean the reservoir cap and surrounding area so no grit falls in, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the port at the bottom — never let the reservoir run dry, or you will pull air straight into the system.
- Top the reservoir up with fresh fluid from your sealed container.
- Slip the clear tubing over the front bleeder valve and route the other end into the catch bottle, positioned so you can see the fluid moving.
- Fit the box-end wrench on the bleeder, then squeeze the front lever firmly and hold it.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the reservoir level as it drops.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air back in through the valve.
- Release the lever slowly, then check and top off the reservoir.
- Repeat the squeeze–hold–open–close–release cycle until the fluid coming through the tube runs clean and free of bubbles, and the lever feels firm.
- If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general habit, start with the caliper farthest from the master cylinder and work toward the closest.
Bleeding the Rear Circuit
- Locate the rear reservoir and confirm it sits level, then open it and remove most of the old fluid with the syringe.
- Refill with fresh fluid and fit the tubing and catch bottle to the rear bleeder.
- Press and hold the rear pedal, open the bleeder a quarter turn, let fluid and air escape, then close the bleeder before releasing the pedal.
- Top off the reservoir, then repeat until the fluid runs clean and bubble-free.
- Keep an eye on the reservoir throughout — the rear circuit holds less than you expect, and it is easy to empty it mid-cycle.
Closing Up and Checking Your Work
When both circuits run clean, snug the bleeder valves down firmly without overtightening — you are sealing against a small copper or aluminum washer, and brute force will damage it. Fill each reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and caliper for any weeping. A dry paper towel pressed against each joint after a few lever strokes will tell you quickly whether anything is seeping.
Proving It Out Before You Ride
Both the lever and the pedal should feel firm and consistent, and should hold that feel when you squeeze or press steadily for several seconds. A lever that slowly sinks toward the grip under constant pressure means there is still air or a leak. Spin each wheel by hand to confirm the brakes are not dragging, then take the bike to an empty lot and test at walking pace, building up speed gradually only once you are satisfied.
When the Lever Won't Come Around
If the lever only firms up after several pumps, if bubbles keep appearing no matter how long you bleed, if fluid is visible at the master cylinder or caliper, or if you suspect air reached the ABS unit, stop and take the bike to a shop. The same applies if you are not confident about the sequence on a system with additional bleed points. Brakes are not the place to guess, and a professional purge costs far less than a failed lever on the road.
Related Shopping Categories
Shop Brake Fluid for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Lines for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Pads for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Stands for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Tools for a 2022 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.