Bleeding the Brakes on a 2021 Kawasaki ZG1400 Concours ABS

Shop parts for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

The 2021 Kawasaki ZG1400 Concours ABS uses hydraulic disc brakes at both ends, and it is equipped with ABS and a linked/combined braking function. That configuration matters before you open a bleeder. A caliper-level bleed is still the familiar way to refresh fluid and push air out of the lines, but this bike has more bleed points and a prescribed order than a simple non-ABS machine. This guide covers a careful fluid flush and air removal at the calipers, and it flags the point where the job should go to a shop.

Why and When a Bleed Is Due

Bleed the Concours when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in either reservoir looks dark, cloudy, or contaminated. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard use, so many riders refresh it on a regular schedule.

Do not confuse a fluid refresh with a pad or rotor job. This article is about removing old fluid and air from the hydraulic system. If the lever is firm but the bike stops poorly, or if a pad is worn or a rotor is scored, address that separately before or after the bleed.

Tools and Supplies to Stage First

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder nipple.
  • A catch bottle for used fluid.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
  • A screwdriver or driver that fits the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder, which can make a one-person job easier.

Use only fluid from a sealed container, and do not reuse fluid that has been sitting open. Brake fluid pulls moisture from the air, and old fluid defeats the purpose of the flush.

Set Up the Bike and Protect the Finish

Support the motorcycle securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front reservoir sits level before you remove the cap. If you are bleeding the rear, make sure the rear reservoir is also in a position where it can be checked and topped off without spilling.

Cover painted surfaces, plastics, and the instrument area with rags before opening any reservoir. Most brake fluid damages paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them on a clean towel, not on the floor where grit can collect.

The Bleeding Procedure, Step by Step

Because this is a linked ABS system, there are extra bleed points and a required sequence. The steps below describe the familiar caliper bleed used to refresh fluid at the calipers. If you are not certain of the correct order for this linked system, or if air may have entered the ABS unit, stop and have a shop perform the bleed rather than guessing.

  1. Open the reservoir you are working on and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry at any point.
  2. Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
  3. Attach the clear tubing to the bleeder valve and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around the nipple.
  4. On a conventional system, start with the caliper farthest from the master cylinder. On this linked ABS bike, use the correct sequence for the system; if you do not have it, do not proceed.
  5. Squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are bleeding.
  6. Open the bleeder about a quarter turn and let fluid and air flow out through the tube. Watch the tube for bubbles and for the color of the fluid.
  7. Close the bleeder before releasing the lever or pedal. Releasing first can draw air back into the system.
  8. Repeat the squeeze, hold, open, close, and release cycle until fresh, clean, bubble-free fluid comes through the tube.
  9. Keep topping off the reservoir throughout the process so it never runs low enough to draw air in. Check the level after every few cycles.
  10. Work one caliper at a time. If there is another front caliper, bleed it after the first, then move to the rear if the rear circuit is hydraulic and included in the procedure.

Finishing Up and Checking for Leaks

When clean fluid runs through the tube with no bubbles, close the bleeder snugly without overtightening it. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check the bleeder and the banjo fittings for weeping or drips. A small seep at a bleeder can feel like a soft lever, so do not skip this check.

Clean the area with water if any fluid touched paint or plastic. Reinstall any covers or bodywork you removed, and make sure the reservoir cap is seated correctly.

Testing Before You Ride

The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever firms up only after several pumps, or if it still feels soft after a complete bleed, there is likely air still in the system.

Troubleshooting and When to See a Shop

A lever that will not firm up after several bleeding attempts, persistent bubbles, fluid leaking from the master cylinder or caliper, or a lever that firms only after pumping all point to a problem that may be beyond a simple caliper bleed. Because this Concours has ABS and linked braking, air that has entered the ABS unit or the linked-system lines may require a shop-level procedure or diagnostic tool. If the reservoir ran dry, if the ABS unit or its lines were disconnected, or if you are unsure of the linked-system bleed order, take the bike to a qualified shop rather than continuing to guess.

Related Shopping Categories

Shop Brake Fluid for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2021 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.