How to Bleed the Brakes on a 2021 Honda NC750X DCT ABS

Shop parts for a 2021 Honda NC750XDCTABS Motorcycle.

The 2021 NC750X DCT ABS stops with hydraulic disc brakes at both ends, and it carries anti-lock braking as part of the package. That gives you two separate hydraulic circuits to look after — a front circuit fed by the lever on the right handlebar and a rear circuit fed by the foot pedal — with the ABS modulator sitting between them. Each circuit is bled on its own, and each has its own reservoir to keep an eye on. The job itself is well within reach of a rider with basic hand tools, provided you work slowly, keep the reservoirs from running dry, and understand the one ABS-specific limitation covered further down.

Confirm the Layout Before You Touch Anything

Take a minute to trace the plumbing on your own bike rather than assuming. Follow the line down from the front master cylinder to the caliper, then find the bleeder valve on that caliper. Do the same at the rear, where the pedal master cylinder is mounted low on the frame and the bleeder sits on the rear caliper. On the NC750X the two circuits are independent, so a soft front lever tells you nothing about the rear, and vice versa. If your particular bike carries two front calipers, treat them as two separate bleed points and do them one at a time. Because this machine has ABS, a normal flush through the caliper bleeders is the correct approach for routine fluid refreshment — but if air has been drawn into the ABS unit itself, the modulator may need a dealer-level procedure or diagnostic tool to purge, and that part of the job is not a home-garage task.

Signs That the System Needs Bleeding

The most obvious clue is feel. A lever that goes soft or spongy, a pedal with a long lazy travel, or a lever that now comes noticeably closer to the grip than it used to all point to air or tired fluid. Pop the reservoir cap and look at the fluid: dark, cloudy, or contaminated fluid is past its useful life. Bleeding is also mandatory after any work that opened the hydraulic system — new lines, caliper service, master cylinder work, or a reservoir that ran dry.

Even with no symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, so hard, repeated braking can boil it and produce fade or a lever that goes long exactly when you need it most. Many riders simply refresh the fluid on a regular interval as preventive maintenance rather than waiting for a problem to appear.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on your master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • Clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for emptying the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, which makes a solo job much easier

Setting Up Safely

Get the bike secure and upright on a stand on level ground. Turn the handlebars so the front reservoir sits level before you open it, otherwise fluid spills the moment the cap comes off. Lay rags over the tank area, the plastics, the instrument cluster, and anything painted near the reservoirs and calipers. Brake fluid attacks paint and many plastics on contact, so wipe up any drip immediately and rinse the area with water if a spill happens. If your bike has a parking brake, confirm it is released before you begin.

Bleeding the Front Circuit, Step by Step

  1. Remove the reservoir cap screws, lift out the diaphragm and cover plate, and set them down clean side up.
  2. Draw most of the old fluid out of the reservoir with the syringe, leaving a little in the bottom so you do not push air into the master cylinder.
  3. Top the reservoir up with fresh fluid from the sealed container.
  4. Push the clear tubing onto the front bleeder and route the other end into the catch bottle, keeping the tube's end submerged in a little old fluid.
  5. Fit the box-end wrench onto the bleeder.
  6. Squeeze the front lever slowly and hold it against its travel.
  7. Open the bleeder about a quarter turn and watch the tube as fluid and air escape.
  8. Close the bleeder fully before the lever reaches the grip, and before you release the lever.
  9. Release the lever slowly and let it return on its own.
  10. Check the reservoir and top it up again — never let it drop low enough to pull air in.
  11. Repeat the squeeze, open, close, release cycle until clean, fresh, bubble-free fluid flows through the tube.
  12. If your bike has two front calipers, repeat the whole sequence on the second caliper. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.

Bleeding the Rear Circuit

The rear follows the same rhythm with the pedal instead of the lever. Locate the rear reservoir, clean around its cap before opening it, and empty most of the old fluid. Refill with fresh fluid, attach the tubing and catch bottle to the rear caliper bleeder, and fit the wrench. Press and hold the pedal, crack the bleeder a quarter turn, close it before the pedal bottoms out, then let the pedal return. Keep the reservoir topped off between cycles and continue until the fluid runs clean and clear of bubbles. Rear reservoirs are often small, so check the level after every few pumps rather than every few minutes.

Finishing Up and Verifying the Job

When the fluid runs clean at both ends, close each bleeder snugly with the box-end wrench — firm enough to seal, never so tight that you risk damaging the valve or the caliper. Fill each reservoir to the level marking, reinstall the diaphragm flat and undistorted, and refit the cap. Wipe down every surface you touched and rinse away any fluid residue. Inspect the bleeder valves and the banjo fittings at the calipers and master cylinders for weeping, then spin each wheel by hand to confirm the brakes are not dragging.

Before riding normally, check that the lever and pedal feel firm and consistent rather than spongy, and hold steady pressure on each for several seconds to confirm neither slowly sinks. Then test the brakes at low speed in a safe, empty area before trusting them in traffic.

When to Stop and Take It to a Shop

If the lever or pedal will not firm up after several honest bleeding attempts, if it only firms after pumping, or if bubbles keep appearing no matter how long you work, stop and have the bike inspected. The same applies to fluid weeping from a master cylinder or caliper, or any situation where the reservoir ran dry or the ABS unit or its lines were disturbed — air trapped in the modulator needs equipment and a procedure beyond a home bleed. A brake system that will not hold a firm, consistent feel is not something to test on the road.

Related Shopping Categories

Shop Brake Fluid for a 2021 Honda NC750XDCTABS Motorcycle.

Shop Brake Lines for a 2021 Honda NC750XDCTABS Motorcycle.

Shop Brake Pads for a 2021 Honda NC750XDCTABS Motorcycle.

Shop Stands for a 2021 Honda NC750XDCTABS Motorcycle.

Shop Brake Tools for a 2021 Honda NC750XDCTABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.