Bleeding the Brakes on a 2021 Honda Africa Twin Adventure Sports ES DCT

Shop parts for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

The 2021 Honda Africa Twin 1100 Adventure Sports ES DCT uses hydraulic disc brakes at both ends and is equipped with ABS. That means the routine service you can do at home is a caliper-level bleed: refreshing fluid and removing air through the bleeders on the front and rear calipers. The ABS unit itself is not a home bleed point on this bike. If air has entered the ABS unit—for example, because the reservoir ran dry or a line was disconnected—the motorcycle should go to a shop with the appropriate equipment. The DCT transmission does not change the hydraulic bleeding steps.

What This Job Covers on the Africa Twin

Bleeding is not the same as replacing pads or rotors. This job moves fresh fluid through the front and rear hydraulic circuits and pushes trapped air out through the caliper bleeders. It is the right service after a spongy lever, a pedal that feels long, or any repair that opened the hydraulic system, such as new lines, caliper work, or master cylinder service. It is also the way to refresh old fluid. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade under hard use, so many riders bleed on a regular schedule even when the brakes still feel acceptable.

Signs That Point to a Bleed

A soft or spongy front lever is the classic clue. So is a lever that now pulls closer to the grip than it used to, or a rear pedal that feels vague before it bites. Look at the fluid in the reservoir: dark, cloudy, or contaminated fluid is a reason to flush. If the lever slowly sinks while you hold steady pressure, that also points to air or a seal issue. Any recent work that let air into the system should be followed by a bleed before normal riding.

Tools and Supplies to Stage First

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder
  • A catch bottle for old fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder, which can make a one-person job easier

Preparing the Bike and Protecting Surfaces

Support the Africa Twin securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them aside where they will not pick up grit.

The Bleeding Procedure, Front and Rear

  1. Open the reservoir and use the syringe or baster to remove most of the old fluid. Do not let the reservoir run dry.
  2. Refill with fresh fluid of the type marked on the reservoir cap.
  3. Attach the clear tube to the bleeder and route the other end into the catch bottle.
  4. Squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are bleeding.
  5. Open the bleeder about a quarter turn to let fluid and air escape.
  6. Close the bleeder before releasing the lever or pedal. Releasing first can draw air back in.
  7. Repeat until fresh, clean, bubble-free fluid comes through the tube. Keep topping off the reservoir throughout so it never runs low enough to draw air into the system.
  8. Work through the front calipers one at a time. As a general practice, start with the caliper farthest from the master cylinder, then move to the other if your bike has a second front caliper.
  9. Bleed the rear hydraulic circuit the same way, using the rear pedal and the rear caliper bleeder.

Finishing, Leak Checks, and a Low-Speed Test

Tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid. Check for leaks at the bleeder and at the banjo fittings. Before riding, the lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.

When the Lever or Pedal Will Not Firm Up

If the lever will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and diagnose rather than continuing to bleed. A lever that never firms can point to air trapped in the ABS unit, a seal problem, or a bleed point that is not being reached by a simple caliper bleed. Any situation where air may have entered the ABS unit is a shop job. The same applies if you are not confident in the procedure or if the bike has any linked-brake hardware that requires a specific sequence. A correct bleed leaves the 2021 Africa Twin Adventure Sports ES DCT with a firm lever, a solid pedal, and brakes that are ready for a careful low-speed check.

Related Shopping Categories

Shop Brake Fluid for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Lines for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Pads for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Stands for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Shop Brake Tools for a 2021 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.