Bleeding the Brakes on a 2020 Kawasaki Z900 RS

Shop parts for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

What This Job Covers on the Z900 RS

The 2020 Kawasaki Z900 RS uses hydraulic disc brakes at both ends, and this model is equipped with ABS. That means there is a front hydraulic circuit operated by the lever and a rear hydraulic circuit operated by the pedal, and both use brake fluid that should be refreshed from time to time. The ABS hardware does not change the basic caliper bleed for routine fluid service, but it does raise the stakes if the reservoir ever runs dry or a hydraulic line is opened. This article covers a fluid flush and air removal at the calipers. It is not a pad, rotor, caliper, or line replacement guide, though those jobs are common reasons a bleed is needed afterward.

When Bleeding Is Needed

A spongy or soft lever or pedal is the classic sign that air is in the system. So is a lever that pulls closer to the grip than it used to, or a pedal that feels longer and less positive than before. Dark or cloudy fluid in the reservoir is another reason to act, even if the brakes still feel acceptable. Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to brake fade under hard use, so many riders refresh it on a regular schedule rather than waiting for a symptom. Bleeding is also required after any work that opened the hydraulic system, such as new lines, caliper service, or master cylinder work.

Tools and Supplies to Gather

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • A length of clear tubing that fits snugly over the bleeder
  • A catch bottle for old fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the manual lever-and-bleeder method works fine with a helper. Keep the fluid container capped when you are not pouring, and do not reuse fluid that has been sitting open.

Preparation Before You Open the System

Support the Z900 RS securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Work in a well-ventilated space and keep the reservoir cap and diaphragm clean so grit does not fall into the fluid.

Step-by-Step Bleeding Procedure

Work on one hydraulic circuit at a time. The front and rear are separate systems on this bike, so treat them as two jobs. If more than one front caliper is fitted, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder.

  1. Open the reservoir and use the syringe or baster to remove most of the old fluid. Do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm.
  3. Attach the clear tubing to the bleeder valve and route the other end into the catch bottle.
  4. Squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are bleeding.
  5. Open the bleeder about a quarter turn to let fluid and air escape through the tube.
  6. Close the bleeder before you release the lever or pedal. This prevents air from being drawn back in.
  7. Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube.
  8. Keep topping off the reservoir throughout the job so it never runs low enough to draw air into the system.
  9. Move to the other front caliper if your bike has more than one, then repeat the process on the rear circuit if you are flushing both ends.

Finishing the Job

When clean fluid is flowing and no bubbles remain, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder and at the banjo fittings. A dry fitting after a bleed is a good sign; a wet fitting needs attention before you ride.

Testing and Troubleshooting

The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever will not firm up after several bleeding attempts, if it firms up only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and have the bike inspected. Because this Z900 RS has ABS, air that has entered the ABS unit itself—for example, after the reservoir ran dry or the ABS unit or its lines were disconnected—may require a shop-level procedure or diagnostic tool. In that situation, the bike should go to a qualified shop rather than being ridden with uncertain brakes.

Related Shopping Categories

Shop Brake Fluid for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Lines for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Pads for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Stands for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Tools for a 2020 Kawasaki ZR900 - Z900 RS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.