Bleeding the Brakes on a 2020 Kawasaki Z900 ABS
Shop parts for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.Understand the System Before You Open It
The 2020 Kawasaki Z900 ABS stops on hydraulic disc brakes at both ends. A master cylinder on the handlebar feeds the front caliper or calipers, and a separate master cylinder operated by the foot pedal feeds the rear caliper. The two circuits are independent — the lever does not work the rear brake and the pedal does not work the front — which means each side can be bled on its own without worrying about a combined sequence.
Because this machine carries the ABS designation, an anti-lock module is plumbed into the hydraulic system. For ordinary maintenance — refreshing old fluid, or removing air that got in at a caliper or a line fitting — a standard bleed through the caliper bleeders is the correct approach. The one situation that changes is air that has traveled into the ABS unit itself, which typically happens if the reservoir ran dry while bleeding, or if the module or its hard lines were disconnected. That kind of air usually will not come out with a hand bleed and needs a dealer-level procedure or diagnostic tool. If you suspect it, stop and take the bike to a shop.
Why and When to Bleed
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture lowers the fluid's boiling point, and a boiling fluid creates vapor that behaves exactly like air in the lines — the lever goes soft and braking performance drops away, often right when you are working the brakes hardest. That is why many riders refresh the fluid on a schedule even when nothing feels wrong.
Bleed sooner if the lever feels spongy or pulls closer to the grip than it used to, if the pedal feels mushy or travels farther than normal, if the fluid in the reservoir looks dark or cloudy, or if you have just replaced a line, serviced a caliper, or had the master cylinder apart. Any of those jobs lets air into the system, and air must come out before the bike is ridden.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so do not use a bottle that has been sitting around
- A box-end wrench that fits the bleeder valve snugly
- A length of clear tubing that fits tightly over the bleeder nipple
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a one-person job easier
- A rear stand or another way to hold the bike securely upright
Set Up and Protect the Finish
Get the bike stable on level ground, on a stand if you have one. For the front circuit, turn the handlebars until the reservoir on the bar sits level, since a tilted reservoir will spill as soon as the cap comes off. Lay rags over the tank or bodywork, the plastics, the instrument cluster, and anything else below the reservoir.
Brake fluid attacks paint and many plastics on contact, so treat every drip as urgent: wipe it up immediately and rinse the area with water. Keep the bottle capped when you are not pouring, and keep the fluid away from the reservoir exterior where it can run down unnoticed.
Bleeding the Front Brake
- Clean the reservoir lid and the area around it so dirt cannot fall in, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Do not pump the lever with the reservoir low — that is how air gets pulled into the line.
- Refill with fresh fluid to a safe working level, leaving room to top off as you go.
- Slip the clear tubing over the front bleeder valve and route the other end into the catch bottle, with the bottle positioned so you can see the fluid moving.
- Squeeze the lever slowly and hold it. With the lever held, open the bleeder about a quarter turn and let the fluid and air escape.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air back in through the nipple.
- Repeat the squeeze–hold–open–close–release cycle, checking the reservoir level every few strokes and topping it off. Never let it run dry.
- If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder and finish with the closest.
- Keep going until the fluid coming through the tubing is clean and free of bubbles, then close the bleeder.
Bleeding the Rear Brake
- Clean the rear reservoir area and open it, then remove most of the old fluid and top up with fresh.
- Fit the clear tubing to the rear bleeder and lead it into the catch bottle.
- Press and hold the pedal, open the bleeder a quarter turn, let fluid and air out, then close the bleeder before releasing the pedal.
- Repeat, watching the reservoir level and refilling as needed, until the fluid runs clean and bubble-free.
- Close the bleeder and top the reservoir to the level marking.
Finishing Up and Checking for Leaks
Tighten the bleeder snugly with the box-end wrench — firm enough to seal, but not so hard that you damage the seat. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder and at the banjo fittings at the master cylinder and caliper for any weeping or wetness, and check again after the bike has sat for a while.
Test Before You Ride
The lever and pedal should feel firm and consistent, and should not slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.
When to Take It to a Shop
If the lever will not firm up after several rounds of bleeding, if it only firms up when you pump it, if bubbles keep appearing no matter how long you bleed, or if you see fluid at the master cylinder or caliper, stop and have the bike inspected. The same applies if the reservoir ran dry or the ABS unit was disturbed — air trapped in the module is a shop job, not a driveway one.
Related Shopping Categories
Shop Brake Fluid for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.
Shop Brake Lines for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.
Shop Brake Pads for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.
Shop Stands for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.
Shop Brake Tools for a 2020 Kawasaki ZR900 - Z900 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.