Bleeding the Brakes on a 2020 Kawasaki Concours 14 ABS

Shop parts for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Understand the System Before You Crack a Bleeder

The 2020 Kawasaki Concours 14 ABS (ZG1400) stops on hydraulic disc brakes at both ends, and as the model name confirms, it carries an anti-lock braking system. That gives you two separate hydraulic circuits to service — a front circuit fed by the reservoir at the lever and a rear circuit fed by the reservoir at the pedal — and each one has its own bleeder points at the caliper end.

There is a second layer of complexity worth naming up front. This generation of Concours uses a combined braking layout, in which the lever and the pedal can influence braking at more than one wheel through additional valving and plumbing. A straightforward fluid refresh through the caliper bleeders is still the normal home-garage job, but the combined hardware means there are more bleed points than a plain two-circuit bike, and the order in which you open them matters. If you cannot confidently identify every bleeder on your machine and the correct order to work through them, hand the job to a shop. A partially bled combined system is a genuine safety risk.

The ABS unit adds one more caveat. Air that enters the system at the calipers or the master cylinder can usually be pushed out with a normal bleed. Air that gets trapped inside the ABS modulator itself — which happens if the reservoir ran dry, or if the ABS unit or its lines were disconnected — generally needs a dealer-level procedure or diagnostic tool to cycle the pump and purge it. Do not attempt to improvise that. If you suspect air is in the modulator, stop and book the bike in.

When a Bleed Is Actually Due

Some riders bleed on symptoms, others on a schedule, and both approaches have merit. Reach for the tools when the front lever feels spongy or pulls noticeably closer to the grip than it used to, when the rear pedal feels soft or travels further before it bites, when the fluid visible in either reservoir has gone dark or cloudy, or after any work that opened the hydraulic system — new lines, caliper service, master cylinder work, or a fluid top-up that let the reservoir run low.

Even with no symptoms at all, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, and a low boiling point shows up as fade under hard, repeated braking — exactly when you need the brakes most. Many riders refresh the fluid on a regular interval as preventive maintenance rather than waiting for the lever to tell them something is wrong. On a heavy sport-tourer like the Concours, that habit is worth keeping.

Tools and Supplies to Have on the Bench

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different specification, and do not use a bottle that has been open and sitting on a shelf.
  • A box-end wrench that fits the bleeder valve snugly. A box-end grips the hex far better than an open-end and is much less likely to round a bleeder.
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in.
  • Rags or shop towels, and a syringe or turkey baster for lifting old fluid out of the reservoirs.
  • The correct driver for the reservoir cap screws.
  • Optional but genuinely helpful for solo work: a one-way check-valve bleeder or a vacuum bleeder.

Set Up and Protect the Bike

Get the machine secure and upright on a stand before anything is opened. Turn the handlebars so the front reservoir sits level, since a reservoir that is tilted will spill as soon as the cap comes off. Drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoirs and bleeders. Brake fluid attacks paint and many plastics on contact, and the damage is permanent. If a drop lands where it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until you finish.

The Bleeding Procedure, Step by Step

  1. Working on one circuit at a time, wipe the reservoir cap and surrounding area clean, then remove the cap and diaphragm.
  2. Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the port at the bottom so you do not push air into the master cylinder.
  3. Refill with fresh fluid from the sealed container, keeping the level well up the sight glass or marking.
  4. Push the clear tubing onto the bleeder nipple and route the other end into the catch bottle, with the bottle positioned so the tube runs uphill away from the bleeder where possible.
  5. Squeeze and hold the lever, or press and hold the pedal, and keep it held.
  6. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the reservoir, while the bleeder is open.
  7. Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper.
  8. Release the lever or pedal slowly, then repeat the squeeze–hold–open–close cycle. Top the reservoir off every few cycles so it never drops low enough to pull air in.
  9. Continue until the fluid coming through the tube runs clean and clear with no bubbles, then close the bleeder and move to the next caliper. If your bike has more than one front caliper, bleed each one in turn rather than trying to do them together.
  10. As a general practice, start with the caliper farthest from its master cylinder and work toward the closest, and follow the sequence your combined system requires for any additional bleed points.
  11. Repeat the whole process for the rear circuit at the pedal, using the same technique.

Finishing Up and Checking for Leaks

Snug each bleeder down firmly with the box-end wrench — tight enough that it will not weep, but not so tight that you distort the caliper threads. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder nipples and the banjo fittings at the calipers and master cylinders for any sign of weeping, and leave the bike sitting for a few minutes before you call it done.

Test Before You Ride in Traffic

The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking while you keep a steady squeeze on them. Spin each wheel by hand to confirm nothing is dragging. Then, in a safe open area at low speed, apply the brakes gently and progressively before riding normally. If anything feels soft, long, or inconsistent, go back and bleed again rather than hoping it settles.

When to Stop and Let a Shop Take Over

Bring the bike to a professional if the lever will not firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you work, if you find fluid weeping from a master cylinder or caliper, or if there is any chance air reached the ABS modulator or the combined-brake hardware. Those are the situations where the right call is a lift, a diagnostic tool, and someone who works on this system regularly.

Related Shopping Categories

Shop Brake Fluid for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2020 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.