How to Bleed the Brakes on a 2020 Kawasaki KLE300 Versys-X 300 ABS
Shop parts for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
The 2020 Kawasaki KLE300 Versys-X 300 ABS uses hydraulic disc brakes at both ends, and the ABS designation confirms an anti-lock braking system is part of the package. That means you have a front brake circuit and a rear brake circuit to service, each with its own master cylinder, reservoir, and caliper. For a normal fluid refresh or a bleed after opening a line, you can work through the caliper bleeders just as you would on a non-ABS bike. The important exception is air that has entered the ABS unit itself; that is a shop-level concern, not a garage bleed. This guide walks you through the job in a safe, logical order so you can restore a firm lever and pedal.
Why and When These Brakes Need Bleeding
Bleeding removes air and old fluid from the hydraulic system. Air is compressible, so even a small bubble can make the front lever feel soft or cause the rear pedal to travel farther than it should. Old fluid is a slower problem: brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade under hard or repeated braking. You should plan a bleed when the lever or pedal feels spongy, when the lever pulls closer to the grip than it used to, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic system—new lines, caliper service, or master cylinder work. Many riders also refresh the fluid on a regular schedule even when the brakes still feel acceptable.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels, plus water for rinsing spills
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier
Brake fluid damages paint and many plastics on contact, so keep rags close and wipe up any spill immediately. Rinse the area with water if fluid reaches painted or plastic surfaces.
Preparation Before You Open the System
Support the bike securely upright on a stand so the reservoirs sit as level as possible. Turn the handlebars so the front reservoir is level before you remove the cap. Cover the area around the front reservoir, the instrument cluster, and any painted or plastic surfaces with rags. For the rear, locate the rear master cylinder reservoir and protect the surrounding bodywork in the same way. Work in a well-ventilated area and keep the fluid container closed when you are not pouring from it.
Bleeding the Front Brake
- Remove the front reservoir cap and diaphragm. Use the syringe or turkey baster to remove most of the old fluid from the reservoir, but do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap. Leave enough air space for the diaphragm to sit correctly later.
- Fit the clear tubing over the front caliper bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around it.
- Squeeze the front lever slowly and hold it. While holding pressure, open the bleeder about a quarter turn with the box-end wrench. Fluid and air will move through the tube.
- Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the caliper.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean fluid comes through the tube with no bubbles. Check the reservoir often and top it off so it never runs low enough to pull air into the master cylinder.
- If your bike has more than one front caliper, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder.
Bleeding the Rear Brake
- Open the rear master cylinder reservoir and remove most of the old fluid without letting the reservoir run dry. Refill with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the rear caliper bleeder and route it into the catch bottle.
- Press and hold the rear brake pedal. Open the bleeder about a quarter turn, let fluid and air escape, then close the bleeder before releasing the pedal.
- Repeat until the fluid in the tube is clean and bubble-free. Keep an eye on the rear reservoir and top it off throughout the process.
Finishing, Testing, and When to Stop
When clean fluid is flowing at both ends, tighten each bleeder snugly without overtightening. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and clean up any spilled fluid. Check for leaks at the bleeder valves and at the banjo fittings. Before riding, the front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.
If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from a master cylinder or caliper, stop and have the bike inspected. Also send the bike to a shop if the reservoir ran dry, if the ABS unit or its lines were disconnected, or if you suspect air has entered the ABS unit itself. A standard caliper bleed is usually enough for routine fluid service on the Versys-X 300 ABS, but ABS-unit air may require a dealer-level procedure or diagnostic tool.
Related Shopping Categories
Shop Brake Fluid for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
Shop Brake Lines for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
Shop Brake Pads for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
Shop Stands for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
Shop Brake Tools for a 2020 Kawasaki KLE300 - Versys-X 300 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.