Bleeding the Brakes on a 2020 Kawasaki ER650/Z650
Shop parts for a 2020 Kawasaki ER650 - Z650 Motorcycle.
The 2020 Kawasaki ER650 — the model most riders know as the Z650 — stops on hydraulic disc brakes at both ends, with an ABS module plumbed into the system. That layout matters for this job: there is a front circuit fed by the lever and a rear circuit fed by the pedal, and each one can be flushed and purged at its own caliper bleeder. Nothing about the work is exotic, but brakes are the one system on the bike where a sloppy shortcut shows up at the worst possible moment. Take your time, keep the reservoir from running dry, and the lever will come back firm.
Why and When This Job Belongs on Your List
Brake fluid is hygroscopic, which is a polite way of saying it pulls moisture out of the air over time. That moisture does two unhelpful things: it lowers the fluid’s boiling point, so hard repeated braking can boil the fluid and give you a lever that goes soft exactly when you need it most, and it darkens the fluid as it degrades. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.
Other triggers are more immediate. A lever that feels spongy or pulls closer to the grip than it used to is the classic sign of air in the line. So is a pedal with a long, vague travel. Dark or cloudy fluid in the sight glass or reservoir is a clear signal. And any time the hydraulic system has been opened — new lines, a caliper rebuild, master cylinder service, or a fluid top-off that let the reservoir run low — air gets in and has to come out.
What the Z650’s Brake Layout Means for This Job
On the 2020 ER650, the front brake is a hydraulic disc system operated by the right-hand lever, and the rear is a hydraulic disc operated by the right-foot pedal. The two circuits are independent — this is not a linked or combined system, so bleeding the front does not bleed the rear, and you will need to service each one separately.
Most 2020 Z650s sold in the U.S. are the ABS-equipped version, and that changes one thing about the job. A routine flush through the caliper bleeders is the normal approach and works fine for refreshing fluid. But if air has actually entered the ABS unit itself — because the reservoir ran dry while you were working, or because the ABS unit or its lines were disconnected — the module may need a dealer-level procedure or diagnostic tool to purge properly. Do not try to improvise that. If you suspect air is trapped in the ABS hardware, stop and take the bike to a shop.
Tools and Supplies to Stage Before You Start
- Fresh brake fluid of the type printed on your master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in. Clear tubing lets you watch for bubbles, which is half the diagnostic value of the job.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.
Setting Up Without Damaging Paint or Plastics
Get the bike upright and stable on a stand so you can work without it shifting. Turn the handlebars until the front reservoir sits level — on a bike with a bar-mounted master cylinder, that usually means turning the bars so the reservoir is parallel to the ground before you remove the cap.
Now cover everything. Brake fluid attacks paint and many plastics on contact, and the reservoir sits directly above the tank, the fairing panels, and the instrument cluster. Drape rags over those surfaces before you open anything. If a drop does land somewhere it shouldn’t, wipe it up immediately and rinse the area with water rather than waiting until you finish.
The Bleeding Procedure, Step by Step
- Start with the front circuit. Wipe the reservoir cap and the area around it clean so grit doesn’t fall in, then remove the cap and the diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough in the bottom that you are not pulling air into the master cylinder port.
- Refill with fresh fluid from your sealed container, leaving room to add more as you work.
- Slip the clear tubing over the front caliper bleeder and route the other end into the catch bottle. Make sure the tubing sits snugly — a loose fit will pull air past the threads and make you chase bubbles that were never in the system.
- Fit the box-end wrench onto the bleeder.
- Squeeze the front lever and hold it firmly against the grip. Hold it there.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. You will feel the lever travel toward the grip as pressure releases.
- Close the bleeder before you release the lever. This order is the whole trick — releasing the lever with the bleeder open draws air straight back into the caliper.
- Release the lever, then repeat the squeeze–hold–open–close–release cycle. Check the reservoir level every few cycles and top it off. Never let it run low enough to gulp air.
- Keep going until the fluid coming through the tube is clean and free of bubbles, and the lever feels firm rather than spongy.
- If your bike has two front calipers, bleed each one in turn, one at a time, using the same cycle. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.
- Move to the rear circuit and repeat the entire process at the rear caliper bleeder, using the pedal instead of the lever: press and hold the pedal, open the bleeder, close it, then release.
Finishing Up and Checking for Leaks
When the fluid runs clean at both ends, tighten each bleeder snugly. Snug is the goal — enough to seal, not enough to distort the seat or strip threads. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder fittings and the banjo fittings at the caliper and master cylinder for any weeping. A dry paper towel pressed against each joint will tell you quickly whether anything is seeping.
Confirming the Job Before You Ride
The lever and pedal should feel firm and consistent, and they should hold. Squeeze the lever and hold steady pressure for a slow count of ten — it should not creep toward the grip. Spin each wheel by hand and confirm the brake is not dragging. Then, in a safe open area at low speed, test the brakes gently before riding normally. If anything feels soft or inconsistent, go back and bleed again rather than hoping it settles in.
When to Hand It to a Shop
If the lever will not firm up after several honest bleeding attempts, if it only firms up when you pump it, if bubbles keep appearing no matter how long you work, or if you see fluid weeping from the master cylinder or a caliper, stop. Those symptoms point to a seal problem or air somewhere you cannot reach with a caliper bleeder. The same applies if the reservoir ran dry or the ABS hardware was disturbed — that is a shop job on an ABS-equipped Z650, and it is not worth improvising on a safety-critical system.
Related Shopping Categories
Shop Brake Fluid for a 2020 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Lines for a 2020 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Pads for a 2020 Kawasaki ER650 - Z650 Motorcycle.
Shop Stands for a 2020 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Tools for a 2020 Kawasaki ER650 - Z650 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.