How to Bleed the Brakes on a 2020 Kawasaki ER650/Z650 ABS
Shop parts for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.The 2020 Kawasaki ER650/Z650 ABS uses hydraulic disc brakes at both ends, and the ABS badge confirms an anti-lock braking system is part of the package. That means a normal caliper bleed is the right starting point for refreshing fluid and removing air from the lines and calipers. It also means you need to respect the ABS unit: if the reservoir has run dry, or if the ABS unit or its lines have been disconnected, air may have entered a part of the system that a simple lever-and-bleeder routine will not clear. In that case, the bike should go to a shop with the appropriate diagnostic equipment.
Bleeding is not difficult, but it is safety-critical. Work slowly, keep the reservoir from running dry, and confirm a firm lever and pedal before you ride.
When a Bleed Is Due
Bleed the brakes when the front lever or rear pedal feels spongy, soft, or inconsistent. A lever that pulls closer to the grip than it used to, or a pedal that sinks under steady pressure, is a sign that air or old fluid is affecting the system. Dark, cloudy, or contaminated fluid in the reservoir is another clear reason to flush and bleed.
You should also bleed after any work that opened the hydraulic system: new brake lines, caliper service, master cylinder work, or a fluid change where air may have been introduced. Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard use, so many riders refresh the fluid on a regular schedule as preventive maintenance.
Gather the Right Supplies
Have everything ready before you open the reservoir. Brake fluid is unforgiving of interruptions and spills.
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works fine with a helper or with patience.
Set Up Safely and Protect the Bike
Support the motorcycle securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Remove the reservoir cap and diaphragm carefully, and set them on a clean rag. Do not let dirt or debris fall into the reservoir.
The Step-by-Step Bleed
- Open the front reservoir and use a syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the bottom so you do not introduce air at the master cylinder.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the container sealed when you are not pouring.
- Attach the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around it.
- If your bike has two front calipers, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder, then move to the other side.
- Squeeze and hold the front lever. With the lever held, open the bleeder about a quarter turn to let fluid and air escape. Close the bleeder before you release the lever. Never release the lever while the bleeder is open, or air can be drawn back into the system.
- Repeat the squeeze-hold-open-close-release sequence. Watch the clear tubing for bubbles. Keep topping off the reservoir throughout so it never runs low enough to draw air in.
- Continue until fresh, clean, bubble-free fluid comes through the tube. Then tighten the bleeder snugly without overtightening, and remove the tubing.
- Move to the rear brake. Open the rear master cylinder reservoir, remove most of the old fluid, and refill with fresh fluid. Attach the clear tube to the rear caliper bleeder and repeat the same press-hold-open-close-release sequence with the pedal.
- Keep checking the rear reservoir level as you work. When clean, bubble-free fluid comes through, tighten the rear bleeder snugly and remove the tubing.
- Top off both reservoirs to the correct level marking, reinstall the diaphragms and caps, and wipe up any spilled fluid.
Finishing and Checking for Leaks
After the bleed, check the bleeder valves and the banjo fittings at the master cylinders and calipers for weeping or drips. A bleeder that is snug but not over-tightened should not leak. Clean any residual fluid from the calipers, lines, and reservoir area, then rinse the surrounding painted and plastic surfaces with water as a precaution.
Make sure the reservoir caps and diaphragms are seated correctly. A cap that is not sealed properly can allow moisture or dirt into the system.
Test Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area before riding normally. If anything feels soft, inconsistent, or weaker than before, stop and investigate before heading into traffic.
Troubleshooting and When to See a Shop
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, air is likely still trapped somewhere. Persistent bubbles at the bleeder, fluid leaking from the master cylinder or caliper, or a lever that slowly sinks under pressure are all reasons to stop and have the system inspected.
Because this is an ABS-equipped 2020 Kawasaki ER650/Z650, any situation where air may have entered the ABS unit itself is best handled by a shop. That includes a reservoir that ran dry during service, or any work that disconnected the ABS unit or its lines. A standard caliper bleed is appropriate for routine fluid service, but it is not a substitute for the dealer-level procedure needed to clear air from the ABS unit.
Related Shopping Categories
Shop Brake Fluid for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Lines for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Pads for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Stands for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Tools for a 2020 Kawasaki ER650 - Z650 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.