Bleeding the Brakes on a 2020 Husqvarna Vitpilen 701

Shop parts for a 2020 Husqvarna Vitpilen 701 Motorcycle.

What You're Working With on the Vitpilen 701

The 2020 Vitpilen 701 stops on hydraulic disc brakes at both ends, and it leaves the factory with an anti-lock braking system watching over the front and rear circuits. That combination shapes the whole job. Because both wheels are hydraulically actuated, both circuits deserve attention when you flush the system — a firm front lever with a mushy rear pedal is not a finished job. Because the bike carries ABS, a normal refresh through the caliper bleeder valves is well within reach of a home mechanic, but air that has worked its way into the ABS unit itself is a different animal and usually needs a dealer-level procedure. The 701 does not use a linked or combined braking system, so the front lever and the rear pedal operate independently and each circuit is bled separately, one at a time.

When a Bleed Is Due

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and a fluid that boils under hard, repeated braking creates vapor in the lines — which feels exactly like a spongy lever and can cost you real stopping power when you need it most. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.

Beyond scheduled maintenance, bleed the brakes when the lever or pedal feels soft or spongy, when the lever creeps closer to the grip than it used to, when the fluid in the reservoir looks dark or cloudy, or after any work that opened the hydraulic system: new lines, caliper service, master cylinder work, or a reservoir that ran dry. On the Vitpilen, a lever that firms up only after a few quick pumps is a classic sign that air is in the circuit.

Tools and Supplies to Gather

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — once a bottle is opened, it starts absorbing moisture, so use new stock
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job much less fiddly

Setting Up Safely

Get the bike secure and upright on a stand before you touch anything. For the front circuit, turn the handlebar so the reservoir on the master cylinder sits level — a tilted reservoir lets fluid spill the moment the cap comes off. Drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir, because brake fluid attacks paint and plastic on contact. If a drop does land somewhere it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.

The Bleeding Procedure

  1. With the bike stable and the reservoir level, remove the cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but stop before the bottom — never let the reservoir run dry, or you'll pull air straight into the system.
  2. Top the reservoir up with fresh fluid from your sealed container.
  3. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so you can see the fluid moving through the tube.
  4. Squeeze the front lever and hold it firm against the grip. Keep steady pressure on it for the entire step.
  5. Open the bleeder about a quarter turn with the box-end wrench. Fluid and any trapped air will push out through the tube. Watch the tube, not the reservoir.
  6. Close the bleeder before you release the lever. Releasing with the bleeder open draws air back in through the nipple, which undoes everything you just did.
  7. Release the lever slowly, then repeat the squeeze-hold-open-close-release cycle. Keep an eye on the reservoir level and top it off every few cycles so it never drops low enough to gulp air.
  8. Continue until the fluid coming through the tube runs clean and clear with no bubbles in it. If your bike has more than one front caliper, bleed each one in turn, finishing the circuit completely before moving on.
  9. Move to the rear circuit and repeat the same sequence with the pedal: press and hold, crack the bleeder, close it, then release. The general practice is to start with the caliper farthest from the master cylinder and work inward, which helps push old fluid and air along in one direction.

Finishing the Job

Once clean, bubble-free fluid is flowing at both ends, close the bleeder valves snugly. Snug is the goal — overtightening can damage the valve seat and create a leak. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and calipers for any weeping or dampness.

Testing Before You Ride

The lever and pedal should feel firm and consistent, and neither should slowly sink while you hold steady pressure on it. Spin each wheel by hand to confirm the brakes aren't dragging. Then, in a safe, empty area, test the brakes at low speed before riding normally. If anything feels vague at walking pace, stop and investigate rather than heading out.

When to Hand It to a Shop

Some problems are best left to a professional. If the lever won't firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you work, or if you find fluid leaking from the master cylinder or a caliper, stop and get the bike looked at. The same goes for any situation where air may have entered the ABS unit — a reservoir that ran dry, or ABS components and lines that were disconnected. That requires equipment and a procedure a home garage generally can't replicate, and it's not a job worth improvising on a safety-critical system.

Related Shopping Categories

Shop Brake Fluid for a 2020 Husqvarna Vitpilen 701 Motorcycle.

Shop Brake Lines for a 2020 Husqvarna Vitpilen 701 Motorcycle.

Shop Brake Pads for a 2020 Husqvarna Vitpilen 701 Motorcycle.

Shop Stands for a 2020 Husqvarna Vitpilen 701 Motorcycle.

Shop Brake Tools for a 2020 Husqvarna Vitpilen 701 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.