Bleeding the Brakes on a 2020 Husqvarna Vitpilen 401
Shop parts for a 2020 Husqvarna Vitpilen 401 Motorcycle.Know the System Before You Open It
The 2020 Vitpilen 401 stops on hydraulic disc brakes at both ends. A hand lever on the right bar pushes fluid to the front caliper, and a foot pedal on the right side works the rear caliper through its own master cylinder and reservoir. The two circuits are completely independent — there is no linking between them — so each one is bled separately, and a problem with one has nothing to do with the other. This bike also left the factory with anti-lock braking, which shapes how far a home bleed should go. Refreshing fluid through the caliper bleeders is a normal garage task on an ABS-equipped machine. Pushing air out of the ABS pump or modulator itself is not, and that distinction comes up again near the end of this article.
When a Bleed Is Actually Due
Most riders bleed because something changed at the controls. A lever that feels soft or spongy, a lever that now comes back closer to the grip than it used to, a pedal with a long mushy travel, or fluid in either reservoir that has gone dark, cloudy, or gritty are all signals that the system needs attention. Any job that opened the hydraulics — new lines, a caliper rebuild, master cylinder work, or a reservoir that ran dry — also demands a bleed before the bike goes back on the road.
There is a second reason that has nothing to do with feel. Brake fluid pulls moisture out of the air over time, and that absorbed water lowers the fluid's boiling point. Under repeated hard braking the fluid can boil and create gas in the lines, which shows up as a lever that suddenly goes long. Riders who commute or ride hard often refresh the fluid on a regular interval even when the lever still feels fine, treating it as cheap insurance rather than a repair.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, bought in a sealed container and used the same day it is opened
- A box-end wrench that fits the bleeder valve on the caliper — a snug fit matters more than the size on the stamp
- A length of clear tubing that pushes firmly over the bleeder nipple without slipping off
- A small catch bottle to hang the tubing into
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job much less fiddly
Prepping the Bike and Protecting the Finish
Get the Vitpilen 401 standing securely upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebar until the front reservoir sits level, because a tilted reservoir will spill the moment the cap comes off. Then drape rags over the tank cover, the plastics around the bars, the instrument cluster, and anything else below the reservoir. Brake fluid attacks paint and clear plastic on contact, and a single drip left sitting will leave a mark. If a spill does happen, wipe it up immediately and rinse the area with water rather than waiting until the job is finished.
Bleeding the Front Brake
- Wipe the reservoir cap and the area around it clean so no grit falls in, then remove the cap and the diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough at the bottom that you are not pulling air into the master cylinder port.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward before it drops. That keeps an air bubble from sitting against the nipple.
- Fit the box-end wrench onto the bleeder.
- Squeeze the front lever slowly and hold it firm against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing, and the lever will travel toward the grip.
- Close the bleeder fully before you release the lever. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common way a home bleed goes wrong.
- Release the lever, then repeat the squeeze, hold, open, close, release cycle. Check the reservoir level every few cycles and top it off — it must never run low enough to gulp air.
- Keep going until the fluid coming through the tubing is clean and free of bubbles, and the lever holds firm instead of fading toward the grip.
If your bike is fitted with two front calipers, bleed each one in turn rather than trying to do both at once. As a general habit, start with the caliper farthest from the master cylinder and work toward the closest one.
Bleeding the Rear Brake
- Clean around the rear reservoir cap, open it, and remove most of the old fluid with the syringe.
- Refill with fresh fluid and refit the diaphragm loosely so fluid does not splash while you work the pedal.
- Attach the tubing to the rear caliper bleeder and drop the other end into the catch bottle.
- Press and hold the pedal down, open the bleeder a quarter turn, let the fluid and air escape, then close the bleeder before letting the pedal return.
- Repeat, watching the reservoir level, until the fluid runs clean and bubble-free and the pedal feels solid underfoot.
Buttoning It Up and Checking for Leaks
Finish by tightening the bleeder snugly with the box-end wrench. Snug is the goal — a bleeder is a small tapered seat and it does not need to be cranked down hard to seal. Fill the reservoir to the level marking molded into the body, refit the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder and at the banjo fittings at both the caliper and the master cylinder for any weeping, and leave a clean rag under each point while you finish up so a slow seep shows itself.
Testing Before You Ride
With the bike still on the stand, pull the front lever and hold steady pressure on it for a slow count. It should feel firm and consistent and should not creep toward the grip. Do the same with the rear pedal. Spin each wheel by hand and confirm the brake is not dragging against the disc. Once the bike is down, ride it at walking pace in a safe, empty area and apply each brake separately before trusting them at speed.
If Something Doesn't Feel Right
A lever that will not firm up after several rounds of bleeding, a lever that only feels good after a few quick pumps, or bubbles that keep appearing no matter how long you work at it all point to air entering somewhere it should not. Fluid weeping from the master cylinder or caliper is a leak that has to be fixed before the bike is ridden. And if the reservoir ever ran dry, or the ABS unit or its lines were disconnected, air may now be sitting inside the ABS modulator. That requires a dealer-level procedure and diagnostic tool to cycle the pump and purge it properly, so stop and take the bike to a shop rather than continuing to pump the lever in the garage.
Related Shopping Categories
Shop Brake Fluid for a 2020 Husqvarna Vitpilen 401 Motorcycle.
Shop Brake Lines for a 2020 Husqvarna Vitpilen 401 Motorcycle.
Shop Brake Pads for a 2020 Husqvarna Vitpilen 401 Motorcycle.
Shop Stands for a 2020 Husqvarna Vitpilen 401 Motorcycle.
Shop Brake Tools for a 2020 Husqvarna Vitpilen 401 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.