Bleeding the Brakes on a 2020 Husqvarna Svartpilen 701
Shop parts for a 2020 Husqvarna Svartpilen 701 Motorcycle.Start by Confirming What Your Bike Has
The 2020 Husqvarna Svartpilen 701 is a hydraulic-brake motorcycle at both ends. The front brake is a disc setup fed by a master cylinder on the right handlebar and operated by the lever; the rear is a disc brake fed by its own master cylinder and operated by the foot pedal. The two systems are independent — the lever works the front only and the pedal works the rear only — so there is no linked or combined braking to worry about here, and no extra bleed points hiding in a proportioning valve.
This model also carries an ABS unit. That matters for one reason: a routine fluid flush done through the caliper bleeders is a normal home-garage job, but if air has been allowed into the ABS unit itself — because the reservoir ran dry, or because the ABS unit or its lines were removed or replaced — the unit may need a dealer-level procedure or diagnostic tool to cycle and purge properly. If that describes your situation, stop reading the procedure below and book the bike in.
The Svartpilen 701 runs a single front caliper, so you will not have a second front caliper to work through. If your bike has been modified to a twin-caliper front end, bleed each caliper separately, one at a time.
How to Tell the Brakes Need Bleeding
The most obvious signal is feel. A lever that has gone soft or spongy, or that now comes back much closer to the grip than it used to, is telling you there is air in the system. The same goes for a rear pedal that feels vague or travels further than normal. A lever that firms up when you pump it and then goes soft again while you hold it is a classic air symptom.
Fluid condition is the other indicator. Pop the reservoir cap and look: fresh fluid is clear and light in color, while fluid that has been in service for a couple of seasons turns dark, cloudy, or murky. Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time, and that moisture lowers the fluid's boiling point. On a hard ride with repeated heavy braking, degraded fluid can boil and cause the lever to go long or fade — exactly when you need the brakes most. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.
You also need to bleed after any work that opened the hydraulic circuit: new brake lines, a caliper rebuild or replacement, or master cylinder service. Air gets in the moment the system is opened, and it has to come back out.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on the shelf.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats properly and is far less likely to round the bleeder than an open-end wrench.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to route the old fluid into.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.
Set Up the Bike and Protect the Finish
Get the bike held securely upright on a stand so it cannot tip while you are working the lever. Turn the handlebar until the front reservoir sits level — a reservoir that is tilted will spill as soon as you open it. Before you touch the cap, drape rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir.
Brake fluid attacks paint and many plastics on contact, and the damage is immediate. If a drop lands anywhere it should not, wipe it up right away and rinse the area with water rather than waiting until you finish the job.
The Bleeding Procedure, Step by Step
- Wipe the reservoir cap and surrounding area clean so no dirt falls in, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave a little in the bottom — do not let the reservoir run dry, because that pulls air straight into the master cylinder.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so you can see the fluid coming through the tube.
- Fit the box-end wrench onto the bleeder.
- Squeeze the front lever several times and hold it firmly against the grip. Hold it there — do not release.
- With the lever held, crack the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not your hands.
- Close the bleeder before you let the lever go. This order matters: releasing the lever with the bleeder open draws air back into the caliper.
- Release the lever, then repeat the squeeze–hold–crack–close cycle. Check the reservoir level every few cycles and top it off so it never drops low enough to suck air.
- Keep cycling until the fluid coming through the tube is clean and free of bubbles, and the lever feels firm rather than spongy.
- Move to the rear brake and repeat the same sequence using the pedal instead of the lever: press and hold the pedal, crack the rear bleeder, close it, then release. Keep the rear reservoir topped up as you go.
- If you are working on a bike with more than one caliper on an axle, finish one caliper completely before moving to the next. As a general rule, start with the caliper farthest from its master cylinder and work toward the closest.
Finishing the Job
Once clean fluid is flowing and the lever and pedal feel right, close the bleeder snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the bleeder seat and create a leak. Pull the tubing off and wipe the caliper area clean.
Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down everything you touched. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for any sign of weeping or wetness. A leak here is not something to ride on.
Test Before You Ride
With the bike still supported, spin each wheel by hand and confirm the brakes are not dragging — a wheel that stops quickly or feels tight means something is binding. Then check feel: the lever and pedal should be firm and consistent, and should hold pressure without slowly sinking toward the grip or the floor while you keep steady force on them.
Take the bike to a quiet, safe area and test the brakes at low speed before riding normally. If anything feels off at walking pace, it will not improve at speed.
When to Stop and Take It to a Shop
If the lever will not firm up after several full bleeding cycles, if it only firms up when you pump it, or if bubbles keep appearing no matter how long you bleed, something else is going on — a worn master cylinder seal, a pinhole in a line, or air trapped somewhere a caliper bleed cannot reach. Fluid weeping from the master cylinder or caliper is the same story.
And if there is any chance air entered the ABS unit on this Svartpilen 701, have the bike serviced by a dealer rather than continuing to pump the lever. A properly bled system is a firm, predictable one; anything less is worth the trip to a shop.
Related Shopping Categories
Shop Brake Fluid for a 2020 Husqvarna Svartpilen 701 Motorcycle.
Shop Brake Lines for a 2020 Husqvarna Svartpilen 701 Motorcycle.
Shop Brake Pads for a 2020 Husqvarna Svartpilen 701 Motorcycle.
Shop Stands for a 2020 Husqvarna Svartpilen 701 Motorcycle.
Shop Brake Tools for a 2020 Husqvarna Svartpilen 701 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.