How to Bleed the Brakes on a 2020 Husqvarna Svartpilen 401
Shop parts for a 2020 Husqvarna Svartpilen 401 Motorcycle.
The 2020 Husqvarna Svartpilen 401 uses hydraulic disc brakes at both ends and is equipped with ABS. That means both the front lever and the rear pedal act on fluid-filled circuits, and both can benefit from a proper bleed. This MotoSport guide walks you through refreshing the fluid and removing air at the caliper bleeders. It also explains where the job stops being a normal garage bleed and becomes an ABS service that should go to a shop.
When the Svartpilen 401 Needs a Brake Bleed
A spongy lever, a pedal that feels softer than usual, or a lever that now pulls closer to the grip are classic signs that air or old fluid is affecting the system. Dark or cloudy fluid in the reservoir is another clue. So is any recent work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work.
Brake fluid absorbs moisture over time. That lowers its boiling point and can contribute to brake fade under hard use, even if the brakes feel normal during easy riding. Many riders refresh the fluid on a regular schedule rather than waiting for a symptom. On the 2020 Svartpilen 401, a standard bleed at the caliper bleeders is generally used to refresh fluid. If air has entered the ABS unit itself—for example, because the reservoir ran dry or the ABS unit or its lines were disconnected—the system may require a dealer-level procedure or diagnostic tool. Do not improvise an ABS bleed at home; take the bike to a shop in that situation.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder valve
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver that matches the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder to make one-person bleeding easier
Use only fresh fluid from a sealed container. Do not top off with fluid that has been sitting open, and do not reuse fluid that has passed through the system.
Set Up the Bike and Protect Sensitive Surfaces
Support the 2020 Svartpilen 401 securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front master cylinder reservoir sits level before you open it. Locate the rear master cylinder reservoir and keep it level as well.
Cover painted surfaces, plastics, and the instrument area with rags before opening any reservoir. Most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep rags handy around the reservoir, the bleeder valve, and the hose connection.
Bleeding the Front Brake, Step by Step
The 2020 Svartpilen 401 uses one front caliper, so you will service that caliper. On any twin-caliper front end, you would bleed each caliper separately and start with the one farthest from the master cylinder.
- Clean the area around the front reservoir cap, then remove the cap and diaphragm.
- Use a syringe or turkey baster to remove most of the old fluid from the reservoir. Do not let the reservoir run completely dry.
- Refill the reservoir with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle.
- Squeeze the front lever several times, then hold it firmly against the grip.
- Open the bleeder valve about a quarter turn with the box-end wrench. Fluid and air will move through the tube.
- Close the bleeder valve before you release the lever. Releasing the lever with the bleeder open can draw air back into the system.
- Release the lever slowly, then repeat the squeeze-hold-open-close sequence.
- Keep checking the reservoir and topping it off with fresh fluid throughout the process. The reservoir must never run low enough to draw air in.
- Continue until fresh, clean, bubble-free fluid comes through the tube. Then close the bleeder snugly without overtightening.
Bleeding the Rear Brake on the Svartpilen 401
The rear brake on this model is hydraulic, so it is bled at the rear caliper rather than adjusted like a mechanical drum brake.
- Clean the rear reservoir area and open the reservoir.
- Remove most of the old fluid without letting the reservoir run dry, then refill with fresh fluid.
- Attach the clear tubing to the rear caliper bleeder valve and route it into the catch bottle.
- Press the rear pedal several times, then hold it down.
- Open the bleeder about a quarter turn, let fluid and air escape, then close the bleeder before releasing the pedal.
- Release the pedal slowly and repeat the press-hold-open-close sequence.
- Keep the rear reservoir topped off with fresh fluid throughout the bleed.
- Stop when the fluid in the tube is clean and free of bubbles. Tighten the bleeder snugly without overtightening.
Finishing Up and Checking for Leaks
Once both circuits are bled, fill each reservoir to the correct level marking. Reinstall the diaphragm and cap. Clean any spilled fluid from the reservoir, caliper, hose, and surrounding surfaces. Check the bleeder valves and the banjo fittings at the master cylinder and caliper for weeping or drips. Pump the front lever and rear pedal several times, then recheck the reservoir levels. If a level drops noticeably, stop and investigate before riding.
Test the Brakes Before Normal Riding
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If either brake feels different from what you expect, do not ride the bike until the issue is resolved.
When to Stop and Take the Bike to a Shop
A lever or pedal that will not firm up after several bleeding attempts, a lever that firms up only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop. Also stop if the reservoir ran dry, if the ABS unit or its lines were disconnected, or if you suspect air has entered the ABS unit. The 2020 Svartpilen 401’s ABS hardware is not a place to guess at a bleed sequence. A shop with the correct procedure and tools should handle that part of the job.
Related Shopping Categories
Shop Brake Fluid for a 2020 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Lines for a 2020 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Pads for a 2020 Husqvarna Svartpilen 401 Motorcycle.
Shop Stands for a 2020 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Tools for a 2020 Husqvarna Svartpilen 401 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.