Bleeding the Brakes on a 2020 Honda Africa Twin 1100

Shop parts for a 2020 Honda Africa Twin 1100 Motorcycle.

The 2020 Honda Africa Twin 1100, also known as the CRF1100L, uses hydraulic disc brakes at both ends and is equipped with ABS. That means a routine bleed is still a caliper-level job for most riders: you are refreshing fluid and pushing air out through the bleeders. The ABS unit adds one important caveat. If the reservoir has run dry, or if the ABS unit or its lines have been opened, air may be trapped where a simple caliper bleed cannot reach it. This guide walks you through a careful front and rear bleed on the Africa Twin 1100, with checks along the way so you know when to continue and when to stop.

When the Africa Twin Needs a Brake Bleed

A spongy front lever, a rear pedal that feels soft or travels farther than it used to, or a lever that pulls closer to the grip are classic signs that air or old fluid is affecting the system. Dark, cloudy, or contaminated fluid in the reservoir is another reason to act. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade under hard use, so many riders refresh it on a regular schedule even when the brakes still feel normal. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work.

Tools and Supplies to Stage First

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • Clear tubing that fits tightly over the bleeder valve
  • A clean catch bottle for used fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier

Use only fluid from a sealed container, and do not reuse fluid that has been sitting open or drained from the system. Have everything within reach before you open the reservoir so you are not searching for a tool while the system is exposed.

Setting Up the Bike Safely

Support the Africa Twin securely upright on a stand so the front reservoir sits level. Turn the handlebars as needed before you open the cap, because a tilted reservoir can spill fluid as soon as the cover comes off. Cover painted surfaces, plastics, and the instrument area with rags. Most brake fluids damage paint and plastic on contact, so wipe up any spill immediately and rinse the area with water if fluid reaches a painted or plastic surface. Keep the reservoir cap and diaphragm clean and set them where they will not pick up grit.

Bleeding the Front Brake Circuit

  1. Open the front master cylinder reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap later.
  3. Fit the clear tubing over the front caliper bleeder valve and route the other end into the catch bottle. Keep the tube routed so you can see bubbles and fluid color.
  4. Squeeze the front lever slowly and hold it against the grip. Keep steady pressure on it.
  5. Open the bleeder about a quarter turn with the box-end wrench. Fluid and any trapped air will move through the tube.
  6. Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the caliper.
  7. Release the lever, then repeat the squeeze-hold-open-close-release sequence. Check the reservoir often and top it off so it never gets low enough to pull air into the master cylinder.
  8. Continue until the fluid coming through the tube is clean, fresh, and free of bubbles. If the Africa Twin has a caliper on each side of the front wheel, bleed one caliper at a time, then repeat the process on the other front caliper. As a general practice, start with the caliper farthest from the master cylinder if you are unsure which side to begin with.

Bleeding the Rear Brake Circuit

  1. Keep the bike upright and confirm the rear reservoir is level and accessible. Remove most of the old fluid without letting the reservoir run dry.
  2. Refill with fresh fluid from the sealed container.
  3. Attach the clear tubing to the rear caliper bleeder and route it into the catch bottle.
  4. Press and hold the rear brake pedal, then open the bleeder about a quarter turn.
  5. Close the bleeder before releasing the pedal. Repeat the press-hold-open-close-release sequence, topping off the reservoir as you go.
  6. Keep going until the fluid in the tube is clean and bubble-free. Watch the reservoir level closely, because the rear circuit holds a small volume and it is easy to draw air in if you let the level fall too far.

Finishing Up and Confirming the Job

When clean fluid is flowing at each bleeder, close the bleeder snugly without overtightening it. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check the bleeder valves and the banjo fittings at the master cylinder and calipers for leaks. Before riding, squeeze the front lever and press the rear pedal: both should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area before riding normally.

If the Brakes Will Not Firm Up

A lever or pedal that will not firm up after several bleeding attempts, a lever that firms only after pumping, persistent bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop and diagnose rather than keep riding. Because the 2020 Africa Twin 1100 is ABS-equipped, any situation where the reservoir ran dry or the ABS unit or its lines were disconnected may require a dealer-level procedure or diagnostic tool to remove air from the ABS unit itself. Do not attempt to guess at an ABS bleed sequence. If you are not confident in the result, have the bike inspected by a qualified shop before riding.

Related Shopping Categories

Shop Brake Fluid for a 2020 Honda Africa Twin 1100 Motorcycle.

Shop Brake Lines for a 2020 Honda Africa Twin 1100 Motorcycle.

Shop Brake Pads for a 2020 Honda Africa Twin 1100 Motorcycle.

Shop Stands for a 2020 Honda Africa Twin 1100 Motorcycle.

Shop Brake Tools for a 2020 Honda Africa Twin 1100 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.