Bleeding the Brakes on a 2020 Honda Africa Twin 1100 Adventure Sports ES

Shop parts for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

The 2020 Honda Africa Twin 1100 Adventure Sports ES is an ABS-equipped adventure bike with hydraulic disc brakes at both ends. A caliper-level bleed is a realistic home-garage job for a rider with basic tools, but the ABS hardware deserves respect. A normal bleed at the caliper bleeders refreshes fluid and removes air from the lines and calipers. If air has entered the ABS unit itself, the job changes and usually belongs at a shop.

Know the Brake Layout First

This MMY has a hydraulic front brake operated by the lever and a hydraulic rear brake operated by the pedal. Each side has its own master cylinder, reservoir, lines, and caliper bleeder. Bleed the front and rear as separate jobs, one at a time, and watch the matching reservoir while you work. Because this Africa Twin 1100 Adventure Sports ES has ABS, do not assume every soft lever is just air in a caliper. If a reservoir ran dry, if the ABS unit or its lines were disconnected, or if the bike was tipped in a way that let air travel upward, the ABS unit may need a dealer-level procedure or diagnostic tool.

When a Bleed Is Due

Bleed when the lever or pedal feels spongy, when the lever pulls closer to the grip than it used to, or when fluid in either reservoir looks dark or cloudy. A bleed is also due after work that opened the hydraulic system, such as new lines, caliper service, or master cylinder work. Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to fade under hard use, so many riders refresh fluid on a regular schedule even without symptoms.

Tools and Supplies

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • Clear tubing that fits tightly over the bleeder nipple.
  • A small catch bottle.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid.
  • The correct driver for the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder for one-person work.

Set Up and Protect the Finish

Support the bike securely upright on a stand so it cannot tip while you work the lever or pedal. Turn the handlebars so the front reservoir sits level before removing the cap. Cover painted bodywork, plastics, the instrument area, and nearby surfaces with rags. Most brake fluid damages paint and plastic on contact. Wipe up any spill immediately and rinse the area with water; do not let fluid sit on a painted surface.

Step-by-Step Bleeding Procedure

  1. Start with the front brake. Open the front reservoir cap and diaphragm, then remove most of the old fluid with a syringe or turkey baster. Leave enough fluid that the bottom port is not exposed to air.
  2. Refill with fresh fluid of the type marked on the cap. Keep the cap and diaphragm nearby, but leave the reservoir open so you can top it off.
  3. Fit the clear tubing over the front caliper bleeder and route the other end into the catch bottle.
  4. If your bike has two front calipers, treat them as separate bleed points and do one at a time. As a general practice, begin with the caliper farther from the master cylinder along the line routing, then bleed the other.
  5. Squeeze the front lever slowly and hold it against the grip. With the lever held, open the bleeder about a quarter turn. Fluid and air will move down the tube. Close the bleeder before releasing the lever; releasing with the bleeder open can draw air back in.
  6. Repeat the squeeze-hold-open-close-release cycle. Watch the tube for bubbles and watch the reservoir level. Top off before the reservoir gets low enough to pull air into the master cylinder.
  7. Continue until the fluid in the tube is clean, fresh-looking, and bubble-free. Close the bleeder snugly without overtightening; excessive force can damage the seat.
  8. Move to the rear brake. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid. Fit the clear tube to the rear caliper bleeder and route it to the catch bottle.
  9. Press and hold the rear pedal, open the bleeder about a quarter turn, let fluid and air out, then close the bleeder before releasing the pedal. Repeat, topping off the rear reservoir, until the fluid is clean and bubble-free.
  10. Check both reservoirs one last time. If either ran low during the bleed, air may have been drawn in, so repeat that circuit until the lever or pedal feels firm and consistent.

Finishing and Testing Before Riding

Tighten each bleeder snugly without overtightening. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away spilled fluid. Check the bleeder valves and banjo fittings at the master cylinder and caliper for wetness or weeping. The front lever and rear pedal should feel firm and consistent, not spongy, and should not slowly sink under steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then test at low speed in a safe area before riding normally.

When to Stop and See a Shop

A lever or pedal that will not firm up after several careful bleeding attempts is a sign to stop. The same is true if the lever firms up only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder, caliper, or a fitting. On this ABS-equipped Africa Twin 1100 Adventure Sports ES, any suspicion that air entered the ABS unit itself is a shop job. The same applies if the bike has a linked brake system with extra bleed points and a required sequence, or if you are not confident you can keep the reservoir from running dry. Brakes are not the place to guess.

Related Shopping Categories

Shop Brake Fluid for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Lines for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Pads for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Stands for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Tools for a 2020 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.