Bleeding the Brakes on a 2020 Honda Africa Twin Adventure Sports ES DCT
Shop parts for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
The Adventure Sports ES is the tall-tank, long-distance trim of the Africa Twin, and its braking hardware is conventional in the best sense: hydraulic disc brakes at both ends, ABS as standard equipment, and a caliper on each side of the front wheel fed by the lever on the right bar. The DCT gearbox changes how you ride the bike, not how the hydraulics are plumbed, so a fluid flush and air purge here follows the same logic you would apply to any modern twin-disc, ABS-equipped adventure machine. What follows covers both circuits — front and rear — in the order most home mechanics tackle them.
What You Are Actually Working On
Your Africa Twin has two completely independent hydraulic circuits. The front lever pressurizes a master cylinder on the handlebar, which pushes fluid down to the calipers on the front wheel. The rear pedal works its own master cylinder and its own reservoir to operate the rear caliper. Between the master cylinders and the calipers sits the ABS modulator, which is the one part of this system that is not really a home-garage item.
A normal bleed at the caliper bleeders pulls fresh fluid through the lines and pushes trapped air out of the calipers and hoses. That is entirely within reach of a careful DIY rider. What a caliper bleed cannot reliably do is clear air that has migrated into the ABS unit itself. If your reservoir ever ran dry while the lever was being pumped, or if the modulator or its hard lines were disconnected, the bike should go to a dealer with the appropriate diagnostic equipment.
Symptoms That Mean It Is Time
The classic warning is a lever that feels soft or spongy and pulls closer to the grip than it used to. A lever that firms up only after two or three quick pumps is telling you air is in the system. On the rear, a pedal that feels vague or travels further before biting is the same message. Dark, cloudy, or gritty-looking fluid in either reservoir is another prompt — fresh fluid is nearly clear.
Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. That absorbed water lowers the fluid's boiling point, and under hard, repeated braking on a loaded adventure bike it can boil and produce exactly the spongy feel you are trying to eliminate. That is why many riders refresh the fluid on a schedule even when nothing feels wrong. Any job that opened the hydraulic system — new lines, caliper service, master cylinder work, or a reservoir that ran low — also calls for a bleed afterward.
Tools and Supplies to Gather First
- Fresh brake fluid of the type printed on your master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing that fits tightly over the bleeder nipple, plus a catch bottle
- Rags or shop towels, and a syringe or turkey baster for lifting old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job easier
Setting Up Before You Open Anything
Get the bike solidly upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebar until the front reservoir sits level; a reservoir that is tilted will spill the moment the cap comes off. Then drape rags over the tank area, the plastics around the bars, and the instrument cluster. Brake fluid attacks paint and many plastics on contact, so wipe up any drip immediately and rinse the area with water if it reaches a painted surface.
Bleeding the Front Circuit, Step by Step
- Remove the reservoir cap and diaphragm, then use the syringe to draw most of the old fluid out. Leave a little in the bottom so you do not push air into the master cylinder.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle low enough that fluid runs downhill.
- Slide the box-end wrench onto the bleeder.
- Squeeze the lever firmly and hold it against its stop.
- Open the bleeder about a quarter turn and watch the tube. Fluid and any air will be pushed out.
- Close the bleeder before you release the lever. Releasing with the bleeder open pulls air straight back into the caliper.
- Release the lever slowly and let it return on its own.
- Check the reservoir and top it up after every few pumps. Letting it run dry is the fastest way to turn a fifteen-minute job into a frustrating one.
- Repeat until the fluid coming through the tube is clean and free of bubbles, then give the bleeder a final snug tighten without overtightening it.
- Move to the caliper on the other side of the front wheel and repeat the whole sequence. As a general habit, start with the caliper farthest from the master cylinder and finish with the closer one.
The Rear Brake
The rear circuit uses the same drill with a different actuator: press and hold the pedal instead of the lever, and keep an eye on the rear reservoir, which is separate from the front and just as easy to drain by accident. Work the pedal through its stroke, crack the rear bleeder a quarter turn, close it, then release. Keep topping the reservoir and continue until the fluid runs clear and bubble-free.
Finishing, Then Proving It Works
Fill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Look closely at the bleeder and at the banjo fittings at the master cylinder and caliper for any weeping, and leave the bike sitting for a few minutes before you call it done. The lever and pedal should feel firm and consistent and should not slowly sink while you hold steady pressure on them. Spin each wheel by hand to confirm nothing is dragging. Then, before any normal riding, test the brakes at low speed in an empty lot.
When to Stop and Book Shop Time
If the lever will not firm up after several honest attempts, if bubbles keep appearing no matter how long you bleed, or if fluid is seeping from the master cylinder or a caliper, put the tools down and get the bike looked at. The same applies any time air may have entered the ABS unit — that is a job for a dealer with the right equipment, not a driveway session.
Related Shopping Categories
Shop Brake Fluid for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Lines for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Pads for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Stands for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Shop Brake Tools for a 2020 Honda Africa Twin 1100 Adventure Sports ES DCT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.