Bleeding the Brakes on a 2020 Ducati Multistrada 1260 S Grand Tour
Shop parts for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
The 2020 Ducati Multistrada 1260 S Grand Tour uses hydraulic disc brakes at both ends and is equipped with ABS. That means the front lever and rear pedal both move fluid through a sealed hydraulic circuit, and both systems can benefit from a proper bleed when the fluid is old or air has entered. A standard bleed at the caliper bleeders is the right approach for routine fluid refresh and for removing air that has collected at the calipers or lines. If air has reached the ABS unit itself, the job changes, and this article will explain when to stop and hand the bike to a shop.
When a Bleed Is Due
Brake fluid absorbs moisture over time, even in a sealed system. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard or repeated use. Many riders refresh brake fluid on a regular schedule even when the brakes feel normal, because clean fluid is cheap insurance for a heavy, fast street bike like the Multistrada 1260 S Grand Tour.
There are also clear symptoms that call for bleeding. A spongy or soft front lever, a lever that pulls closer to the grip than it used to, a rear pedal that feels vague, or fluid that looks dark or cloudy in the reservoir are all signs to act. Bleeding is also necessary after work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Do not wait for a lever to reach the grip before checking the system.
Tools and Supplies to Gather
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier for one person, but neither is required. The clear tubing matters because it lets you watch the fluid and any air bubbles as they leave the caliper.
Preparation Before Opening the System
Support the bike securely upright on a stand so it cannot tip while you work. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Work in a well-ventilated area and keep the reservoir cap and diaphragm clean. Before removing the cap, wipe around it so dirt does not fall into the fluid. Once the reservoir is open, do not let it run dry at any point during the bleed. That is the most common way to draw air into a system that was previously working correctly.
Step-by-Step Bleeding Procedure
- Open the front reservoir and use a syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the reservoir that the master cylinder inlet stays covered, and do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the container sealed until you pour, and cap it again afterward.
- Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle. Position the bottle so the tubing stays below the bleeder and cannot pull fluid back into the caliper.
- Squeeze and hold the front lever. With the lever held, open the bleeder about a quarter turn to let fluid and air escape. Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the system.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tubing. Check the reservoir often and top it off before it gets low.
- If your bike has two front calipers, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder, then move to the other side.
- Move to the rear brake and repeat the same process with the rear pedal. Open the rear reservoir, remove most of the old fluid, refill with fresh fluid, attach the tubing to the rear bleeder, and press and hold the pedal while you open and close the bleeder. Keep the rear reservoir topped off throughout.
- Continue each circuit until the fluid in the tubing is clean and free of bubbles, and the lever or pedal feels firm. Do not reuse fluid that has passed through the system.
Finishing the Job
Tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the reservoir, caliper, and surrounding surfaces. Check for leaks at the bleeder and at the banjo fittings. A dry fitting after a bleed is a good sign, but recheck after the first few brake applications.
Testing Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If anything feels inconsistent, stop and investigate before heading into traffic.
Troubleshooting and When to See a Shop
A lever that will not firm up after several bleeding attempts, a lever that firms up only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop. Because this Multistrada is ABS-equipped, air that has entered the ABS unit itself may require a dealer-level procedure or diagnostic tool. If the reservoir ran dry, the ABS unit or its lines were disconnected, or the lever still will not firm up after a careful bleed, take the bike to a shop rather than continuing to guess.
Related Shopping Categories
Shop Brake Fluid for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
Shop Brake Lines for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
Shop Brake Pads for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
Shop Stands for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
Shop Brake Tools for a 2020 Ducati Multistrada 1260 S Grand Tour Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.