How to Bleed the Brakes on a 2019 Kawasaki Concours 14 ABS

Shop parts for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Know the System Before You Open It

The 2019 Kawasaki Concours 14 ABS — the ZG1400 — stops on hydraulic disc brakes at both ends, and it is a sophisticated system. The bike carries anti-lock braking, and it also uses a linked arrangement in which the rear pedal influences a front caliper and the front lever influences the rear circuit. That linkage is the single most important thing to understand before you touch a bleeder, because it means the bike has more bleed points than a plain two-circuit motorcycle and a defined order for working through them.

For a routine fluid refresh — the kind of job this article covers — a careful home mechanic can do good work at the calipers. What you should not attempt is improvising a sequence for the linked system or trying to purge air that has traveled up into the ABS modulator. If the reservoir has ever run dry, if a line or the ABS unit has been off the bike, or if you simply are not certain of the correct order, hand the bike to a shop with the diagnostic equipment to cycle the pump. Air trapped in the modulator will not come out by pumping the lever in your garage, and a lever that feels fine at a standstill can go long on the first hard application.

Signs That the Fluid Needs Attention

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture does two unhelpful things: it lowers the fluid's boiling point, so hard repeated braking can generate vapor and a soft, fading lever, and it darkens the fluid and encourages corrosion inside the calipers and master cylinder. That is why many riders on a touring machine like the Concours refresh the fluid on a schedule even when nothing feels wrong.

Watch for a lever that pulls closer to the grip than it used to, a pedal with a spongy or vague first inch of travel, fluid in the reservoir that looks dark, cloudy, or has visible sediment, and any recent work that opened the hydraulics — new lines, caliper service, master cylinder repair. Any of those is your cue to bleed.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type.
  • A box-end wrench that fits the bleeder valve snugly — a six-point box end is far less likely to round the hex than an open end.
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in.
  • A syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws.
  • Rags or shop towels, and a spray bottle of water for rinsing spills.
  • Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.

Set Up and Protect the Bike

Get the Concours upright and stable on a stand so the reservoirs sit level. Turn the handlebars until the front master cylinder is horizontal before you remove the cap — a tilted reservoir spills. Drape rags over the bodywork, the instrument cluster, the screen, and anything painted near the bars and the rear master cylinder, because brake fluid attacks paint and plastic almost on contact. If a drop lands anyway, wipe it immediately and rinse the area with water rather than waiting until you finish.

The Bleeding Procedure, Step by Step

  1. Clean the reservoir cap and surrounding area so grit cannot fall in, then remove the cap and diaphragm.
  2. Draw most of the old fluid out of the reservoir with the syringe or baster. Leave the bottom covered — never let the reservoir run dry, or you will pump air straight into the system.
  3. Top up with fresh fluid from the sealed container.
  4. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged.
  5. Squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are working.
  6. Open the bleeder about a quarter turn. Fluid and any air will push out through the tube.
  7. Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air back in through the nipple.
  8. Repeat the squeeze–hold–open–close–release cycle, topping off the reservoir as the level drops, until clean, fresh, bubble-free fluid flows through the tube.
  9. Move to the next bleed point. As a general practice, start with the caliper farthest from the master cylinder and work toward it, and if your bike has two front calipers, bleed each one in turn rather than trying to do both at once.
  10. Because this is a linked system with more than one bleed point, work through every one of them in the correct order. If you are not confident of that order, stop and let a shop finish the job.

Finishing Up and Checking for Leaks

When the fluid runs clean at every point, close the bleeder snugly — firm, not forced. Overtightening can crush the seat and create a leak that is worse than the one you were chasing. Refill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder nipples and the banjo fittings at the master cylinders and calipers for weeping, and leave the bike a few minutes before checking again.

Test Before You Ride

With the bike still stationary, pull the lever and press the pedal. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Then find a quiet, low-speed area and test the brakes gently before riding normally — a linked ABS system can feel different from a conventional one, and you want to learn its behavior somewhere safe.

When to Stop and Call a Shop

If the lever will not firm up after several rounds of bleeding, if it only firms after pumping, if bubbles keep appearing no matter how long you work, or if you find fluid seeping from a master cylinder or caliper, the problem is beyond a simple flush. The same applies to any bike that may have swallowed air into the ABS unit or that has a linked system you are unsure how to sequence. On a safety-critical system like this one, a shop visit is cheap insurance.

Related Shopping Categories

Shop Brake Fluid for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2019 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.