Bleeding the Brakes on a 2019 Husqvarna Svartpilen 701

Shop parts for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Start With the Svartpilen 701's Brake Layout

The 2019 Svartpilen 701 uses hydraulic disc brakes at both ends, and it is an ABS-equipped machine. That combination shapes the whole job. Because both the front and rear brakes are hydraulic, both get bled when you flush the system. Because the bike has ABS, a routine fluid refresh done through the caliper bleeder valves is still a normal garage task — the ABS pump does not need to run for a simple flush. The exception is air that has traveled into the ABS unit itself, which can happen if the reservoir ran dry, or if the ABS unit or its lines were disconnected during other work. That situation usually needs a dealer-level procedure or a diagnostic tool, and it is not something to improvise at home.

The front lever and the rear pedal on this bike work independently, so you will bleed each circuit on its own. If your particular bike is fitted with more than one front caliper, work through them one at a time rather than trying to bleed both at once.

How to Tell the Brakes Need Bleeding

The most obvious clue is feel. A lever that has gone spongy, or that now pulls noticeably closer to the grip than it used to, is telling you air or degraded fluid is in the system. The rear pedal can go soft in the same way. Look at the fluid in the reservoir as well: fresh fluid is clear and pale, while fluid that has gone dark, cloudy, or murky has absorbed moisture and picked up contamination.

Brake fluid is hygroscopic, meaning it draws moisture out of the air over time. That moisture lowers the fluid's boiling point, and under hard or repeated braking the fluid can boil and produce fade — a lever that goes long exactly when you need it most. That is why many riders refresh the fluid on a regular interval even when nothing feels wrong. Bleeding is also mandatory after any work that opened the hydraulic system: new lines, caliper service, or master cylinder work.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • Clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job easier

Set Up the Bike and Protect the Finish

Get the Svartpilen 701 supported securely upright on a stand so it cannot tip while you are working the lever. For the front circuit, turn the handlebars until the reservoir sits level; a reservoir that is tilted will spill as soon as you open it. Lay rags over the painted bodywork, the plastics, and the instrument area before you touch anything. Brake fluid damages paint and plastic on contact, so any drip should be wiped up immediately and the area rinsed with water.

Bleeding the Front Brake

  1. Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out. Leave a little in the bottom so you do not push air into the master cylinder.
  2. Refill with fresh fluid from the sealed container and set the cap loosely back in place to keep debris out.
  3. Push the clear tubing onto the front caliper bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
  4. Squeeze the front lever and hold it firm.
  5. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing.
  6. Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
  7. Repeat the squeeze, hold, open, close, release cycle, topping off the reservoir as you go. Never let the level drop far enough to pull air into the master cylinder.
  8. Keep going until the fluid coming through the tubing is clean and free of bubbles, then finish with the lever held and the bleeder closed.

Bleeding the Rear Brake

  1. Open the rear reservoir and remove most of the old fluid, then top it up with fresh fluid.
  2. Fit the tubing over the rear caliper bleeder and run it into the catch bottle.
  3. Press and hold the rear pedal, open the bleeder a quarter turn, then close it before releasing the pedal.
  4. Repeat until the fluid runs clean and bubble-free, checking the reservoir level between cycles.

If you are working on a bike with more than one caliper on an end, bleed the caliper farthest from the master cylinder first, then move to the closer one.

Finishing Up and Checking for Leaks

Tighten the bleeder snugly with the box-end wrench — firm is enough, and overtightening can damage the seat. Fill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the calipers and master cylinders for weeping or wetness. A leak here will undo the whole job.

Test Before You Ride

The lever and pedal should feel firm and consistent, not spongy, and should hold steady under a long, hard squeeze without slowly sinking. Spin each wheel to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.

When to Stop and Take It to a Shop

If the lever will not firm up after several rounds of bleeding, if it only firms up after pumping, or if bubbles keep appearing no matter how long you work, stop and have the bike inspected. The same applies to fluid leaking from a master cylinder or caliper, and to any situation where air may have entered the ABS unit. Those cases are beyond a home bleed and belong with a technician who can cycle the ABS system properly.

Related Shopping Categories

Shop Brake Fluid for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Shop Brake Lines for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Shop Brake Pads for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Shop Stands for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Shop Brake Tools for a 2019 Husqvarna Svartpilen 701 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.