Bleeding the Brakes on a 2019 Husqvarna Svartpilen 401
Shop parts for a 2019 Husqvarna Svartpilen 401 Motorcycle.Know the System Before You Touch It
The 2019 Svartpilen 401 stops on hydraulic disc brakes at both ends. A lever-mounted master cylinder feeds the front caliper, and a pedal-driven master cylinder feeds the rear, so you are servicing two independent hydraulic circuits rather than one. The bike also left the factory with ABS, which means an ABS unit sits in the hydraulic path between the master cylinders and the calipers. That detail shapes the whole job: a normal fluid flush through the caliper bleeders is a straightforward garage task, but air that has worked its way into the ABS pump is a different problem entirely and is covered near the end of this article.
Because both wheels are hydraulically braked, plan on bleeding the front and the rear. Do them as separate jobs, one circuit at a time, and finish and check the first before opening the second. That way a mistake on one end never leaves you guessing about the other.
Signs It Is Time to Bleed
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture lowers the fluid’s boiling point, and fluid that boils under hard, repeated braking creates vapor in the lines — which feels exactly like air and behaves exactly as badly. That is why many riders refresh the fluid on a schedule even when nothing feels wrong.
Bleed sooner if any of these show up:
- The front lever feels spongy or soft rather than firm, or it now travels closer to the grip than it used to.
- The rear pedal feels mushy or has more travel than you remember.
- Fluid in either reservoir looks dark, cloudy, or gritty.
- You have just replaced a line, serviced a caliper, rebuilt a master cylinder, or done anything else that opened the hydraulic system to air.
- The lever or pedal slowly sinks while you hold steady pressure at a stop.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
- Clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.
Set Up and Protect the Bike
Get the machine secure and upright on a stand so it cannot tip while you are leaning on the lever. For the front circuit, turn the handlebar until the reservoir sits level — a reservoir that is tilted will spill the moment you open it. Lay rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir.
Brake fluid attacks paint and many plastics on contact, so treat every drip as urgent. Wipe spills immediately and rinse the area with water. Keep the rags you use away from painted bodywork when you set them down.
Bleeding the Front Brake
- Clean the reservoir cap and surrounding area so no dirt falls in, then remove the cap and the diaphragm.
- Draw most of the old fluid out of the reservoir with the syringe, leaving the bottom covered so you do not push air into the master cylinder.
- Top up with fresh fluid from the sealed container.
- Fit the box-end wrench over the front bleeder, push the clear tubing onto the nipple, and route the other end into the catch bottle.
- Squeeze the lever slowly and hold it against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube.
- Close the bleeder fully before you release the lever. Releasing with the bleeder open draws air straight back in.
- Release the lever and let it return on its own.
- Repeat the squeeze, open, close, release cycle, checking the tube each time and topping the reservoir off every few strokes so it never runs low.
- Keep going until the fluid coming through the tube is clean and free of bubbles, then hold the lever and close the bleeder snugly.
If your bike carries two front calipers, bleed them one at a time rather than both at once. The usual practice is to start with the caliper farthest from the master cylinder and work back toward it.
Bleeding the Rear Brake
- Level the rear reservoir, clean around the cap, and open it.
- Remove most of the old fluid, then refill with fresh fluid.
- Attach the wrench and clear tubing to the rear bleeder and lead the tube to the catch bottle.
- Press the pedal and hold it down.
- Crack the bleeder a quarter turn and let fluid and air escape.
- Close the bleeder before letting the pedal up.
- Release the pedal, then repeat, topping the reservoir as you go.
- Continue until the fluid runs clean and bubble-free, then close the bleeder snugly.
Finishing the Job
Snug both bleeders down firmly without overtightening — you are sealing a small tapered seat, not torquing a structural bolt. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe away every trace of fluid. Then look closely at the bleeder and at the banjo fittings at the caliper and master cylinder for weeping or dampness.
Test Before You Ride
Both the lever and the pedal should feel firm and consistent, and neither should creep toward the end of its travel while you hold steady pressure. Spin each wheel and listen and feel for drag that was not there before. Then ride slowly in a safe, open area and apply the brakes gently before trusting them at speed.
When to Hand It to a Shop
If the lever will not firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if fluid is leaking from a master cylinder or caliper, stop and get the bike looked at. The same applies if the reservoir ever ran dry or if the ABS unit or its lines were disconnected — air in the ABS pump generally needs a dealer-level procedure or diagnostic tool to purge, and that is not a job to improvise at home.
Related Shopping Categories
Shop Brake Fluid for a 2019 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Lines for a 2019 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Pads for a 2019 Husqvarna Svartpilen 401 Motorcycle.
Shop Stands for a 2019 Husqvarna Svartpilen 401 Motorcycle.
Shop Brake Tools for a 2019 Husqvarna Svartpilen 401 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.