Bleeding the Brakes on a 2019 Honda Africa Twin DCT
Shop parts for a 2019 Honda Africa Twin DCT Motorcycle.Confirm the Layout Before You Touch Anything
The 2019 Africa Twin DCT uses hydraulic disc brakes at both ends, and the model is equipped with ABS. The front lever works the front caliper or calipers and the rear pedal works the rear caliper as a separate circuit – this is not a linked or combined system, so each end is bled independently and there is no special sequence to follow between them. That is good news for a home mechanic, because it means the job is a straightforward two-circuit flush rather than a system with cross-connected bleed points.
The ABS part deserves a moment of attention. A normal bleed at the caliper bleeders is exactly the right way to refresh fluid and clear air from the lines and calipers on this bike. What a caliper bleed will not do is purge air that has found its way inside the ABS modulator itself. That only happens if the reservoir ran dry, a line was disconnected, or the ABS unit was removed or replaced. If any of those things occurred, the bike needs a dealer-level procedure with a diagnostic tool, and no amount of pumping at the caliper will fix it.
Why and When a Bleed Is Due
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture does two harmful things: it lowers the fluid's boiling point, so hard, repeated braking can boil the fluid and give you a soft, fading lever, and it corrodes the internals of the master cylinder and calipers. That is why many riders refresh the fluid on a schedule even when the brakes feel fine.
On top of the calendar, bleed whenever you notice symptoms. A lever that feels spongy or pulls closer to the grip than it used to, a pedal with a mushy first inch of travel, fluid in the reservoir that looks dark or cloudy rather than clear, or a lever that firms up only after a few quick pumps all point to air or degraded fluid. You also need a bleed after any work that opened the hydraulic system – new lines, caliper service, or master cylinder work.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type and do not use a bottle that has been open for months.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much less fiddly.
Set Up the Bike and Protect the Finish
Get the Africa Twin securely upright on a stand so it cannot tip while you are working the lever. For the front circuit, turn the handlebars until the reservoir on the master cylinder sits level – a tilted reservoir will spill the moment you open the cap. Drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir, because brake fluid attacks paint and plastic on contact. If a drop does land somewhere it shouldn't, wipe it up immediately and rinse the area with water.
Bleeding the Front Brake Circuit
- Clean the reservoir cap and the area around it so no grit falls in, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the bottom so you do not push air into the master cylinder.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the front bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
- Squeeze the front lever and hold it against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing. Watch the tube, not the reservoir, while the bleeder is open.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
- Release the lever slowly and repeat the squeeze-hold-open-close-release cycle. Keep an eye on the reservoir and top it off every few cycles so it never runs low enough to pull air in.
- Continue until the fluid coming through the tubing is clean and free of bubbles, then close the bleeder.
- If your bike has two front calipers, bleed each one in turn using the same cycle. As a general practice, start with the caliper farthest from the master cylinder and finish with the closer one.
Bleeding the Rear Brake Circuit
- Check that the rear reservoir is level and accessible, clean around the cap, and open it.
- Remove most of the old fluid, refill with fresh, and fit the tubing to the rear bleeder.
- Press and hold the brake pedal, open the bleeder a quarter turn, let the fluid and air escape, then close the bleeder before releasing the pedal.
- Repeat, topping off the reservoir as you go, until the fluid runs clean and bubble-free.
Finishing Up and Checking for Leaks
Tighten the bleeder snugly with the box-end wrench – firm enough to seal, but never so hard that you crush the seat or strip the threads. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder and at the banjo fittings at the master cylinder and caliper for any weeping or wetness. A leak here will undo the whole job.
Test Before You Ride
The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking while you hold them. Spin each wheel and confirm the brakes are not dragging. Then, in a safe, empty area, test the brakes at low speed before riding normally. If anything feels soft or inconsistent, stop and diagnose rather than riding it out.
When to Hand It to a Shop
If the lever will not firm up after several full bleeding cycles, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if you see fluid weeping from the master cylinder or a caliper, stop and let a shop look at it. The same applies if the reservoir ever ran dry or if the ABS unit or its lines were disturbed – that is the one scenario on this bike where a home bleed cannot finish the job.
Related Shopping Categories
Shop Brake Fluid for a 2019 Honda Africa Twin DCT Motorcycle.
Shop Brake Lines for a 2019 Honda Africa Twin DCT Motorcycle.
Shop Brake Pads for a 2019 Honda Africa Twin DCT Motorcycle.
Shop Stands for a 2019 Honda Africa Twin DCT Motorcycle.
Shop Brake Tools for a 2019 Honda Africa Twin DCT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.