Bleeding the Brakes on a 2018 Kawasaki Z900 RS

Shop parts for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Know the Layout Before You Touch Anything

The 2018 Kawasaki Z900 RS (ZR900) uses hydraulic disc brakes at both ends, and the RS left the factory with anti-lock braking as part of the package. The front lever and the rear pedal each run their own independent circuit — there is no linked or combined braking on this model — so the front and rear are bled separately, each with its own reservoir, master cylinder, and caliper bleeder. That independence is good news for a home mechanic: a routine flush done through the caliper bleeders is well within reach of anyone comfortable with hand tools. The one thing you should not attempt in the garage is purging air that has worked its way into the ABS modulator itself. That requires a dealer-level diagnostic procedure, and it is covered at the end of this article.

Why and When a Bleed Is Due

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and a boiling fluid creates vapor in the lines — which feels exactly like air in the system and shows up as a soft, fading lever when you need the brakes most. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.

Bleed the system if the front lever feels spongy or pulls closer to the grip than it used to, if the rear pedal feels vague or travels further than normal, if the fluid in either reservoir looks dark or cloudy, or any time the hydraulic system has been opened — new lines, caliper service, master cylinder work, or a reservoir that ran dry. On the Z900 RS, the front reservoir is the small unit on the handlebar and the rear reservoir is the remote cup tucked near the right footpeg area, so check both.

Tools and Supplies to Gather

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so buy what you need and don't reuse an old bottle
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much easier

Set Up and Protect the Finish

Get the bike held securely upright on a stand so neither reservoir can spill. For the front, turn the handlebar until the reservoir on the bar sits level before you loosen the cap. Brake fluid attacks paint and many plastics on contact, so drape rags over the top of the front fairing, the instrument cluster, the handlebar controls, and the area around the rear reservoir before you open anything. If a drop lands on a painted surface, wipe it up immediately and rinse the area with water rather than rubbing it in.

Bleeding the Front Brake

  1. Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out. Leave a little in the bottom so you don't push air into the master cylinder.
  2. Top the reservoir up with fresh fluid and keep it near the full line for the rest of the job.
  3. Slip the clear tubing over the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
  4. Fit the box-end wrench on the bleeder, then squeeze the front lever and hold it firm.
  5. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the reservoir level as you do this.
  6. Close the bleeder before you release the lever. Releasing with the bleeder open draws air back in through the nipple.
  7. Repeat the squeeze–hold–open–close–release cycle, topping the reservoir off as needed, until the fluid coming through the tube runs clean and free of bubbles.
  8. If your bike carries two front calipers, bleed each one in turn rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.

Bleeding the Rear Brake

  1. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid.
  2. Attach the tubing and catch bottle to the rear caliper bleeder and set the wrench in place.
  3. Press and hold the brake pedal, crack the bleeder a quarter turn, then close it before releasing the pedal.
  4. Continue the cycle until clean, bubble-free fluid flows, keeping the reservoir topped off throughout. Never let it run low enough to pull air in — that turns a simple flush into a much longer job.

Finishing Up and Checking for Leaks

Once clean fluid is flowing at both ends, close each bleeder snugly with the box-end wrench. Snug is the goal — these are small fittings, and overtightening can damage the seat. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder nipples and the banjo fittings at the master cylinders and calipers for any weeping or dampness, and check under the bike for drips after a few minutes.

Test Before You Ride

The front lever and rear pedal should both feel firm and consistent, with no sponginess, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes aren't dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If anything feels off, stop and diagnose rather than riding it out.

When to Hand It to a Shop

Bring the bike to a professional if the lever won't firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid leaking from a master cylinder or caliper. On this ABS-equipped Z900 RS, any situation where air may have entered the ABS unit — a reservoir that ran dry, or a modulator or line that was disconnected — is a shop job, since the modulator needs a dealer-level procedure to purge correctly.

Related Shopping Categories

Shop Brake Fluid for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Lines for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Pads for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Stands for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Shop Brake Tools for a 2018 Kawasaki ZR900 - Z900 RS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.