Bleeding the Brakes on a 2018 Kawasaki Z650/ER650
Shop parts for a 2018 Kawasaki ER650 - Z650 Motorcycle.Know What You Are Working On
The 2018 Kawasaki ER650/Z650 uses hydraulic disc brakes at both ends. The front lever and the rear pedal each push fluid through a sealed circuit to a caliper, and both circuits can collect air and moisture over time. The rear brake is not a mechanical drum, so it is bled rather than adjusted. The front and rear circuits are separate on this model, so each must be serviced on its own. ABS-equipped Z650s add an ABS modulator to the hydraulic system. A normal caliper bleed is still the right way to refresh fluid and remove air from the calipers and lines, but if the reservoir has run dry or the ABS unit or its lines have been opened, air can be trapped in the modulator. That is not a home-garage bleed; it needs a dealer-level procedure or diagnostic tool.
When a Bleed Is Due
A spongy or soft front lever, a rear pedal that feels vague, or a lever that pulls closer to the grip than it used to are all signs that air or old fluid is affecting the system. Dark or cloudy fluid in the reservoir is another clear indicator. You should also bleed the brakes after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can lead to brake fade under hard use, so many riders refresh the fluid on a regular schedule as preventive maintenance.
Gather the Right Supplies Before You Start
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- A motorcycle stand or another secure way to hold the bike upright
- Optional: a one-way check-valve bleeder or vacuum bleeder, which can make the job easier for one person
Set Up the Bike and Protect the Finish
Support the Z650 securely upright on a stand. For the front brake, turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Work in a well-ventilated space, and keep the fresh fluid container closed when you are not pouring from it so it does not absorb moisture from the air.
Bleeding the Front Brake, Step by Step
- Remove the reservoir cap and diaphragm, then use a syringe or turkey baster to remove most of the old fluid from the reservoir. Do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
- Attach the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around it.
- Squeeze and hold the front lever. Keep steady pressure on it.
- Open the bleeder about a quarter turn to let fluid and air escape through the tubing. Close the bleeder before you release the lever.
- Release the lever, then repeat the squeeze-hold-open-close-release sequence. Check the tubing for bubbles and watch the fluid color.
- Keep topping off the reservoir throughout the process so it never runs low enough to draw air into the system.
- Continue until fresh, clean, bubble-free fluid comes through the tube. If your Z650 has more than one front caliper, bleed each one in turn, starting with the caliper farthest from the master cylinder.
Bleeding the Rear Brake
- Locate the rear reservoir and make sure it is level and accessible. Remove the cap and diaphragm, then remove most of the old fluid without letting the reservoir run dry.
- Refill with fresh fluid of the type marked on the cap.
- Fit the clear tubing over the rear caliper bleeder valve and route it into the catch bottle.
- Press and hold the rear pedal, open the bleeder about a quarter turn, then close the bleeder before releasing the pedal.
- Repeat the press-hold-open-close-release sequence, topping off the reservoir as needed, until the fluid in the tube is clean and free of bubbles.
Finishing Up and Testing Before You Ride
When the fluid runs clean at both ends, tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder valves and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area.
When to Stop and Take It to a Shop
If the lever or pedal will not firm up after several bleeding attempts, if it firms up only after pumping, or if persistent air bubbles keep appearing, stop and have the bike inspected. Fluid leaking from the master cylinder or caliper also needs professional attention. On an ABS-equipped Z650, any situation where air may have entered the ABS unit—such as a reservoir that ran dry or disconnected ABS lines—should go to a shop with the proper diagnostic equipment. A brake system that will not hold a firm feel is not safe to ride, and a professional inspection is the right call when the home bleed does not solve the problem.
Related Shopping Categories
Shop Brake Fluid for a 2018 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Lines for a 2018 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Pads for a 2018 Kawasaki ER650 - Z650 Motorcycle.
Shop Stands for a 2018 Kawasaki ER650 - Z650 Motorcycle.
Shop Brake Tools for a 2018 Kawasaki ER650 - Z650 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.